$ DeviceNet Electronic Data Sheet For FR-A700 $ $ $ Modification History $ v1.1 2005-01-30 $ v2.0 2005-03-10 Monitor change etc. [File] DescText = "EDS for A700"; CreateDate = 01-30-2005; CreateTime = 00:00:00; ModDate = 03-10-2005; Revision = 2.0; [Device] VendCode = 161; $ VendName = "Mitsubishi Electric"; $ ProdType = 2; $ ProdTypeStr = "AC Drive"; $ ProdCode = 48; $ MajRev = 1; $ MinRev = 1; $ ProdName = "A700"; $ Catalog = "FR-A7ND"; $ [IO_Info] Default = 0x0001; $ support only poll command PollInfo = 0x0001, 2, 2; $ poll, DefaultProduce, DefaultConsume Input1 = 4, $ Size 0, $ Number of Significant Bits 0x0001, $ Compatible I/O Type Mask "Status", $ Name String 6, $ Connection Path Size "20 04 24 46 30 03", $ Connection Path ""; $ Help String Input2 = 4, $ Size 0, $ Number of Significant Bits 0x0001, $ Compatible I/O Type Mask "Status", $ Name String 6, $ Connection Path Size "20 04 24 47 30 03", $ Connection Path ""; $ Help String Output1 = 4, $ Size 0, $ Number of Significant Bits 0x0001, $ Compatible I/O Type Mask "Status", $ Name String 6, $ Connection Path Size "20 04 24 14 30 03", $ Connection Path ""; $ Help String Output2 = 4, $ Size 0, $ Number of Significant Bits 0x0001, $ Compatible I/O Type Mask "Status", $ Name String 6, $ Connection Path Size "20 04 24 15 30 03", $ Connection Path ""; $ Help String [ParamClass] MaxInst = 541; Descriptor = 0x09; CfgAssembly = 0; [Params] $Reserved, Link Path Size, Link Path, Descriptor, Data type, Data Size, Parameter Name, Units String, Help String, Min Value, Max Value, Default Value, Mul, Div, Base, Offset, Param1 = 0, 6, "20 28 24 01 30 03", 0x0002, 0xC6, 1, "Motor Type", "", "", 0, 7, 7, 1, 1, 1, 0, , , , , 0; Param2 = 0, 6, "20 28 24 01 30 07", 0x0000, 0xC7, 2, "Rated Voltage", "Volt", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param3 = 0, 6, "20 29 24 01 30 03", 0x0002, 0xC1, 1, "Run1", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param4 = 0, 6, "20 29 24 01 30 04", 0x0002, 0xC1, 1, "Run2", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param5 = 0, 6, "20 29 24 01 30 05", 0x0002, 0xC1, 1, "Net Control", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param6 = 0, 6, "20 29 24 01 30 06", 0x0032, 0xC6, 1, "State", "", "", 0, 7, 3, 1, 1, 1, 0, , , , , 0; Param7 = 0, 6, "20 29 24 01 30 07", 0x0032, 0xC1, 1, "Running1", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param8 = 0, 6, "20 29 24 01 30 08", 0x0032, 0xC1, 1, "Running2", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param9 = 0, 6, "20 29 24 01 30 09", 0x0032, 0xC1, 1, "Ready", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param10 = 0, 6, "20 29 24 01 30 0A", 0x0032, 0xC1, 1, "Faulted", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param11 = 0, 6, "20 29 24 01 30 0C", 0x0002, 0xC1, 1, "Fault Reset", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param12 = 0, 6, "20 29 24 01 30 0F", 0x0032, 0xC1, 1, "Control From Net", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param13 = 0, 6, "20 29 24 01 30 8C", 0x0000, 0xC6, 1, "Input Assembly", "", "", 0, 255, 71, 1, 1, 1, 0, , , , , 0; Param14 = 0, 6, "20 29 24 01 30 8D", 0x0000, 0xC6, 1, "Output Assembly", "", "", 0, 255, 21, 1, 1, 1, 0, , , , , 0; Param15 = 0, 6, "20 2A 24 01 30 03", 0x0032, 0xC1, 1, "At Reference", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param16 = 0, 6, "20 2A 24 01 30 04", 0x0002, 0xC1, 1, "Net Reference", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param17 = 0, 6, "20 2A 24 01 30 06", 0x0012, 0xC6, 1, "Drive Mode", "", "", 0, 0, 0, 1, 1, 1, 0, , , , , 0; Param18 = 0, 6, "20 2A 24 01 30 07", 0x0030, 0xC7, 2, "Speed Actual", "RPM", "", 0, 32767, 0, 1, 1, 1, 0, , , , , 0; Param19 = 0, 6, "20 2A 24 01 30 08", 0x0000, 0xC7, 2, "Speed Reference", "RPM", "", 0, 32767, 0, 1, 1, 1, 0, , , , , 0; Param20 = 0, 6, "20 2A 24 01 30 09", 0x0074, 0xC7, 2, "Current Actual", "Amp", "", 0, 32767, 0, 1, 1, 1, 0, , , , , 1; Param21 = 0, 6, "20 2A 24 01 30 11", 0x0030, 0xC7, 2, "Output Voltage", "Volt", "", 0, 32767, 0, 1, 1, 1, 0, , , , , 1; Param22 = 0, 6, "20 2A 24 01 30 12", 0x0000, 0xC7, 2, "Acceleration time", "msec", "", 0, 65535, 5000, 1, 1, 1, 0, , , , , 1; Param23 = 0, 6, "20 2A 24 01 30 13", 0x0000, 0xC7, 2, "Deceleration time", "msec", "", 0, 65535, 10000, 1, 1, 1, 0, , , , , 1; Param24 = 0, 6, "20 2A 24 01 30 14", 0x0000, 0xC7, 2, "Low Speed Limit", "RPM", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param25 = 0, 6, "20 2A 24 01 30 15", 0x0000, 0xC7, 2, "High Speed Limit", "RPM", "", 0, 65535, 3600, 1, 1, 1, 0, , , , , 0; Param26 = 0, 6, "20 2A 24 01 30 1D", 0x0032, 0xC1, 1, "Reference From Net", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param27 = 0, 6, "20 2A 24 01 30 70", 0x0044, 0xC7, 2, "Running Frequency (RAM)", "Hz", "", 0, 40000, 0, 1, 1, 1, 0, , , , , 2; Param28 = 0, 6, "20 2A 24 01 30 72", 0x0020, 0xC7, 2, "R:INV Status / W:Ctrl Input Command", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param29 = 0, 6, "20 2A 24 01 30 78", 0x0022, 0xC7, 2, "Operation Mode", "", "", 0, 0x0014, 4, 1, 1, 1, 0, , , , , 0; Param30 = 0, 6, "20 2A 24 01 30 8D", 0x0020, 0xC7, 2, "R:Alarm History1 / W:Alarm History Clear", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param31 = 0, 6, "20 2A 24 01 30 8E", 0x0030, 0xC7, 2, "Alarm History2", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param32 = 0, 6, "20 2A 24 01 30 8F", 0x0030, 0xC7, 2, "Alarm History3", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param33 = 0, 6, "20 2A 24 01 30 90", 0x0030, 0xC7, 2, "Alarm History4", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param34 = 0, 6, "20 2A 24 01 30 91", 0x0030, 0xC7, 2, "Alarm History5", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param35 = 0, 6, "20 2A 24 01 30 92", 0x0030, 0xC7, 2, "Alarm History6", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param36 = 0, 6, "20 2A 24 01 30 93", 0x0030, 0xC7, 2, "Alarm History7", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param37 = 0, 6, "20 2A 24 01 30 94", 0x0030, 0xC7, 2, "Alarm History8", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param38 = 0, 6, "20 80 24 01 30 0B", 0x0074, 0xC7, 2, "Output Frequency", "Hz", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 2; Param39 = 0, 6, "20 80 24 01 30 0D", 0x0074, 0xC7, 2, "Output Voltage", "Volt", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param40 = 0, 6, "20 80 24 01 30 0F", 0x0074, 0xC7, 2, "Frequency setting", "Hz" , "", 0, 65535, 0, 1, 1, 1, 0, , , , , 2; Param41 = 0, 6, "20 80 24 01 30 10", 0x0074, 0xC7, 2, "Running speed", "RPM", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param42 = 0, 6, "20 80 24 01 30 11", 0x0074, 0xC7, 2, "Motor torque", "%", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param43 = 0, 6, "20 80 24 01 30 12", 0x0074, 0xC7, 2, "Converter output voltage", "Volt", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param44 = 0, 6, "20 80 24 01 30 13", 0x0074, 0xC7, 2, "Regenerative brake duty", "%", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param45 = 0, 6, "20 80 24 01 30 14", 0x0074, 0xC7, 2, "Electronic thermal relay function load factor", "%", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param46 = 0, 6, "20 80 24 01 30 16", 0x0074, 0xC7, 2, "Converter output voltage peak value", "Volt", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param47 = 0, 6, "20 80 24 01 30 19", 0x0074, 0xC7, 2, "Input terminal status", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param48 = 0, 6, "20 80 24 01 30 1A", 0x0074, 0xC7, 2, "Output terminal status", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param49 = 0, 6, "20 80 24 01 30 1B", 0x0074, 0xC7, 2, "Load meter", "%", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param50 = 0, 6, "20 80 24 01 30 1D", 0x0074, 0xC7, 2, "Position pulse", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param51 = 0, 6, "20 80 24 01 30 1E", 0x0074, 0xC7, 2, "Cumulative energization time", "h", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param52 = 0, 6, "20 80 24 01 30 20", 0x0074, 0xC7, 2, "Orientation status", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param53 = 0, 6, "20 80 24 01 30 21", 0x0074, 0xC7, 2, "Actual operation time", "h", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param54 = 0, 6, "20 80 24 01 30 22", 0x0074, 0xC7, 2, "Motor load factor", "%", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param55 = 0, 6, "20 80 24 01 30 2A", 0x0074, 0xC7, 2, "Torque command", "%", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param56 = 0, 6, "20 80 24 01 30 2B", 0x0074, 0xC7, 2, "Torque current command", "%", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param57 = 0, 6, "20 80 24 01 30 2D", 0x0074, 0xC7, 2, "Feedback pulse", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param58 = 0, 6, "20 80 24 01 30 30", 0x0074, 0xC7, 2, "Trace status", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param59 = 0, 6, "20 80 24 01 30 3E", 0x0074, 0xC7, 2, "PID set point", "%", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param60 = 0, 6, "20 80 24 01 30 3F", 0x0074, 0xC7, 2, "PID measurement value", "%", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param61 = 0, 6, "20 80 24 01 30 40", 0x0074, 0xC7, 2, "PID deviation value", "%", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param62 = 0, 6, "20 80 24 01 30 44", 0x0074, 0xC7, 2, "Input terminal monitor 1 for communication option", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param63 = 0, 6, "20 80 24 01 30 45", 0x0074, 0xC7, 2, "Input terminal monitor 2 for communication option", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param64 = 0, 6, "20 80 24 01 30 46", 0x0074, 0xC7, 2, "Output terminal monitor 1 for communication option", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param65= 0, 6, "20 70 24 01 30 0A", 0x44, 0xC7, 2, "(Pr0) Torque boost", "%", "", 0, 300, 60, 1, 1, 1, 0, , , , , 1; Param66= 0, 6, "20 70 24 01 30 0B", 0x44, 0xC7, 2, "(Pr1) Maximum frequency", "Hz", "", 0, 12000, 12000, 1, 1, 1, 0, , , , , 2; Param67= 0, 6, "20 70 24 01 30 0C", 0x44, 0xC7, 2, "(Pr2) Minimum frequency", "Hz", "", 0, 12000, 0, 1, 1, 1, 0, , , , , 2; Param68= 0, 6, "20 70 24 01 30 0D", 0x44, 0xC7, 2, "(Pr3) Base frequency", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param69= 0, 6, "20 70 24 01 30 0E", 0x44, 0xC7, 2, "(Pr4) Multi-speed setting(high-speed)", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param70= 0, 6, "20 70 24 01 30 0F", 0x44, 0xC7, 2, "(Pr5) Multi-speed setting(middle-speed)", "Hz", "", 0, 40000, 3000, 1, 1, 1, 0, , , , , 2; Param71= 0, 6, "20 70 24 01 30 10", 0x44, 0xC7, 2, "(Pr6) Multi-speed setting(low-speed)", "Hz", "", 0, 40000, 1000, 1, 1, 1, 0, , , , , 2; Param72= 0, 6, "20 70 24 01 30 11", 0x44, 0xC7, 2, "(Pr7) Acceleration time", "Sec", "", 0, 36000, 50, 1, 1, 1, 0, , , , , 1; Param73= 0, 6, "20 70 24 01 30 12", 0x44, 0xC7, 2, "(Pr8) Deceleration time", "Sec", "", 0, 36000, 50, 1, 1, 1, 0, , , , , 1; Param74= 0, 6, "20 70 24 01 30 14", 0x44, 0xC7, 2, "(Pr10) DC injection brake operation frequency", "Hz", "", 0, 65535, 300, 1, 1, 1, 0, , , , , 2; Param75= 0, 6, "20 70 24 01 30 15", 0x44, 0xC7, 2, "(Pr11) DC injection brake operation time", "Sec", "", 0, 65520, 5, 1, 1, 1, 0, , , , , 1; Param76= 0, 6, "20 70 24 01 30 16", 0x44, 0xC7, 2, "(Pr12) DC injection brake operation voltage", "%", "", 0, 300, 40, 1, 1, 1, 0, , , , , 1; Param77= 0, 6, "20 70 24 01 30 17", 0x44, 0xC7, 2, "(Pr13) Starting frequency", "Hz", "", 0, 6000, 50, 1, 1, 1, 0, , , , , 2; Param78= 0, 6, "20 70 24 01 30 18", 0x44, 0xC7, 2, "(Pr14) Load pattern selection", "", "", 0, 5, 0, 1, 1, 1, 0, , , , , 0; Param79= 0, 6, "20 70 24 01 30 19", 0x44, 0xC7, 2, "(Pr15) Jog frequency", "Hz", "", 0, 40000, 500, 1, 1, 1, 0, , , , , 2; Param80= 0, 6, "20 70 24 01 30 1A", 0x44, 0xC7, 2, "(Pr16) Jog acceleration/deceleration time", "Sec", "", 0, 36000, 5, 1, 1, 1, 0, , , , , 1; Param81= 0, 6, "20 70 24 01 30 1B", 0x44, 0xC7, 2, "(Pr17) MRS input selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param82= 0, 6, "20 70 24 01 30 1C", 0x44, 0xC7, 2, "(Pr18) High-speed maximum frequency", "Hz", "", 12000, 40000, 12000, 1, 1, 1, 0, , , , , 2; Param83= 0, 6, "20 70 24 01 30 1D", 0x44, 0xC7, 2, "(Pr19) Base frequency voltage", "Volt", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param84= 0, 6, "20 70 24 01 30 1E", 0x44, 0xC7, 2, "(Pr20) Acceleration/deceleration reference frequency", "Hz", "", 100, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param85= 0, 6, "20 70 24 01 30 1F", 0x44, 0xC7, 2, "(Pr21) Acceleration/deceleration time increments", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param86= 0, 6, "20 70 24 01 30 20", 0x44, 0xC7, 2, "(Pr22) Stall prevention operation level", "%", "", 0, 4000, 1500, 1, 1, 1, 0, , , , , 1; Param87= 0, 6, "20 70 24 01 30 21", 0x44, 0xC7, 2, "(Pr23) Stall prevention operation level compensation factor at double speed", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param88= 0, 6, "20 70 24 01 30 22", 0x44, 0xC7, 2, "(Pr24) Multi-speed setting(speed 4)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param89= 0, 6, "20 70 24 01 30 23", 0x44, 0xC7, 2, "(Pr25) Multi-speed setting(speed 5)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param90= 0, 6, "20 70 24 01 30 24", 0x44, 0xC7, 2, "(Pr26) Multi-speed setting(speed 6)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param91= 0, 6, "20 70 24 01 30 25", 0x44, 0xC7, 2, "(Pr27) Multi-speed setting(speed 7)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param92= 0, 6, "20 70 24 01 30 26", 0x44, 0xC7, 2, "(Pr28) Multi-speed input compensation selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param93= 0, 6, "20 70 24 01 30 27", 0x44, 0xC7, 2, "(Pr29) Acceleration/deceleration pattern selection", "", "", 0, 5, 0, 1, 1, 1, 0, , , , , 0; Param94= 0, 6, "20 70 24 01 30 28", 0x44, 0xC7, 2, "(Pr30) Regenerative function selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param95= 0, 6, "20 70 24 01 30 29", 0x44, 0xC7, 2, "(Pr31) Frequency jump 1A", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param96= 0, 6, "20 70 24 01 30 2A", 0x44, 0xC7, 2, "(Pr32) Frequency jump 1B", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param97= 0, 6, "20 70 24 01 30 2B", 0x44, 0xC7, 2, "(Pr33) Frequency jump 2A", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param98= 0, 6, "20 70 24 01 30 2C", 0x44, 0xC7, 2, "(Pr34) Frequency jump 2B", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param99= 0, 6, "20 70 24 01 30 2D", 0x44, 0xC7, 2, "(Pr35) Frequency jump 3A", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param100= 0, 6, "20 70 24 01 30 2E", 0x44, 0xC7, 2, "(Pr36) Frequency jump 3B", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param101= 0, 6, "20 70 24 01 30 2F", 0x44, 0xC7, 2, "(Pr37) Speed display", "", "", 0, 9998, 0, 1, 1, 1, 0, , , , , 0; Param102= 0, 6, "20 70 24 01 30 33", 0x44, 0xC7, 2, "(Pr41) Up-to-frequency sensitivity", "%", "", 0, 1000, 100, 1, 1, 1, 0, , , , , 1; Param103= 0, 6, "20 70 24 01 30 34", 0x44, 0xC7, 2, "(Pr42) Output frequency detection", "Hz", "", 0, 40000, 600, 1, 1, 1, 0, , , , , 2; Param104= 0, 6, "20 70 24 01 30 35", 0x44, 0xC7, 2, "(Pr43) Output frequency detection for reverse rotation", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param105= 0, 6, "20 70 24 01 30 36", 0x44, 0xC7, 2, "(Pr44) Second acceleration/deceleration time", "Sec", "", 0, 36000, 50, 1, 1, 1, 0, , , , , 1; Param106= 0, 6, "20 70 24 01 30 37", 0x44, 0xC7, 2, "(Pr45) Second deceleration time", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param107= 0, 6, "20 70 24 01 30 38", 0x44, 0xC7, 2, "(Pr46) Second torque boost", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param108= 0, 6, "20 70 24 01 30 39", 0x44, 0xC7, 2, "(Pr47) Second V/F(Base frequency)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param109= 0, 6, "20 70 24 01 30 3A", 0x44, 0xC7, 2, "(Pr48) Second stall prevention operation current", "%", "", 0, 2200, 1500, 1, 1, 1, 0, , , , , 1; Param110= 0, 6, "20 70 24 01 30 3B", 0x44, 0xC7, 2, "(Pr49) Second stall prevention operation frequency", "Hz", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 2; Param111= 0, 6, "20 70 24 01 30 3C", 0x44, 0xC7, 2, "(Pr50) Second output frequency detection", "Hz", "", 0, 40000, 3000, 1, 1, 1, 0, , , , , 2; Param112= 0, 6, "20 70 24 01 30 3E", 0x44, 0xC7, 2, "(Pr52) DU/PU main display data selection", "", "", 0, 100, 0, 1, 1, 1, 0, , , , , 0; Param113= 0, 6, "20 70 24 01 30 40", 0x44, 0xC7, 2, "(Pr54) FM terminal function selection", "", "", 1, 53, 1, 1, 1, 1, 0, , , , , 0; Param114= 0, 6, "20 70 24 01 30 41", 0x44, 0xC7, 2, "(Pr55) Frequency monitoring reference", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param115= 0, 6, "20 70 24 01 30 43", 0x44, 0xC7, 2, "(Pr57) Restart coasting time", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param116= 0, 6, "20 70 24 01 30 44", 0x44, 0xC7, 2, "(Pr58) Restart cushion time", "Sec", "", 0, 600, 10, 1, 1, 1, 0, , , , , 1; Param117= 0, 6, "20 70 24 01 30 45", 0x44, 0xC7, 2, "(Pr59) Remote function selection", "", "", 0, 3, 0, 1, 1, 1, 0, , , , , 0; Param118= 0, 6, "20 70 24 01 30 46", 0x44, 0xC7, 2, "(Pr60) Energy saving control selection", "", "", 0, 4, 0, 1, 1, 1, 0, , , , , 0; Param119= 0, 6, "20 70 24 01 30 48", 0x44, 0xC7, 2, "(Pr62) Ref. I for intelligent mode accel ", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param120= 0, 6, "20 70 24 01 30 49", 0x44, 0xC7, 2, "(Pr63) Ref. I for intelligent mode decel ", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param121= 0, 6, "20 70 24 01 30 4A", 0x44, 0xC7, 2, "(Pr64) Starting frequency for elevator mode", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param122= 0, 6, "20 70 24 01 30 4B", 0x44, 0xC7, 2, "(Pr65) Retry selection", "", "", 0, 5, 0, 1, 1, 1, 0, , , , , 0; Param123= 0, 6, "20 70 24 01 30 4C", 0x44, 0xC7, 2, "(Pr66) Stall prevention operation reduction starting frequency", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param124= 0, 6, "20 70 24 01 30 4D", 0x44, 0xC7, 2, "(Pr67) Number of retries at alarm occurrence", "", "", 0, 110, 0, 1, 1, 1, 0, , , , , 0; Param125= 0, 6, "20 70 24 01 30 4E", 0x44, 0xC7, 2, "(Pr68) Retry waiting time", "Sec", "", 0, 100, 10, 1, 1, 1, 0, , , , , 1; Param126= 0, 6, "20 70 24 01 30 4F", 0x44, 0xC7, 2, "(Pr69) Retry count display erasure", "", "", 0, 0, 0, 1, 1, 1, 0, , , , , 0; Param127= 0, 6, "20 70 24 01 30 50", 0x44, 0xC7, 2, "(Pr70) Special regenerative brake duty", "%", "", 0, 300, 0, 1, 1, 1, 0, , , , , 1; Param128= 0, 6, "20 70 24 01 30 51", 0x44, 0xC7, 2, "(Pr71) Applied motor", "", "", 0, 54, 0, 1, 1, 1, 0, , , , , 0; Param129= 0, 6, "20 70 24 01 30 52", 0x44, 0xC7, 2, "(Pr72) PWM frequency selection", "", "", 0, 25, 2, 1, 1, 1, 0, , , , , 0; Param130= 0, 6, "20 70 24 01 30 53", 0x44, 0xC7, 2, "(Pr73) Analog input selection", "", "", 0, 17, 1, 1, 1, 1, 0, , , , , 0; Param131= 0, 6, "20 70 24 01 30 54", 0x44, 0xC7, 2, "(Pr74) Input filter time constant", "", "", 0, 8, 1, 1, 1, 1, 0, , , , , 0; Param132= 0, 6, "20 70 24 01 30 55", 0x44, 0xC7, 2, "(Pr75) Reset selection/disconnected PU detection/PU stop selection", "", "", 0, 117, 14, 1, 1, 1, 0, , , , , 0; Param133= 0, 6, "20 70 24 01 30 56", 0x44, 0xC7, 2, "(Pr76) Alarm code output selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param134= 0, 6, "20 70 24 01 30 57", 0x54, 0xC7, 2, "(Pr77) Parameter write selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param135= 0, 6, "20 70 24 01 30 58", 0x44, 0xC7, 2, "(Pr78) Reverse rotation prevention selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param136= 0, 6, "20 70 24 01 30 59", 0x54, 0xC7, 2, "(Pr79) Operation mode selection", "", "", 0, 7, 0, 1, 1, 1, 0, , , , , 0; Param137= 0, 6, "20 70 24 01 30 5B", 0x44, 0xC7, 2, "(Pr81) Number of motor poles", "", "", 2, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param138= 0, 6, "20 70 24 01 30 5D", 0x44, 0xC7, 2, "(Pr83) Rated motor voltage", "Volt", "", 0, 10000, 2000, 1, 1, 1, 0, , , , , 1; Param139= 0, 6, "20 70 24 01 30 5E", 0x44, 0xC7, 2, "(Pr84) Rated motor frequency", "Hz", "", 5000, 12000, 6000, 1, 1, 1, 0, , , , , 2; Param140= 0, 6, "20 70 24 01 30 63", 0x44, 0xC7, 2, "(Pr89) Speed control gain", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param141= 0, 6, "20 70 24 01 30 69", 0x44, 0xC7, 2, "(Pr95) Online auto tuning selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param142= 0, 6, "20 70 24 01 30 6A", 0x44, 0xC7, 2, "(Pr96) Auto-tuning setting/status", "", "", 0, 103, 0, 1, 1, 1, 0, , , , , 0; Param143= 0, 6, "20 71 24 01 30 0A", 0x44, 0xC7, 2, "(Pr100) V/F1 (first frequency)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param144= 0, 6, "20 71 24 01 30 0B", 0x44, 0xC7, 2, "(Pr101) V/F1 (first frequency voltage)", "Volt", "", 0, 10000, 0, 1, 1, 1, 0, , , , , 1; Param145= 0, 6, "20 71 24 01 30 0C", 0x44, 0xC7, 2, "(Pr102) V/F2 (second frequency)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param146= 0, 6, "20 71 24 01 30 0D", 0x44, 0xC7, 2, "(Pr103) V/F2 (second frequency voltage)", "Volt", "", 0, 10000, 0, 1, 1, 1, 0, , , , , 1; Param147= 0, 6, "20 71 24 01 30 0E", 0x44, 0xC7, 2, "(Pr104) V/F3 (third frequency)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param148= 0, 6, "20 71 24 01 30 0F", 0x44, 0xC7, 2, "(Pr105) V/F3 (third frequency voltage)", "Volt", "", 0, 10000, 0, 1, 1, 1, 0, , , , , 1; Param149= 0, 6, "20 71 24 01 30 10", 0x44, 0xC7, 2, "(Pr106) V/F4 (fourth frequency)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param150= 0, 6, "20 71 24 01 30 11", 0x44, 0xC7, 2, "(Pr107) V/F4 (fourth frequency voltage)", "Volt", "", 0, 10000, 0, 1, 1, 1, 0, , , , , 1; Param151= 0, 6, "20 71 24 01 30 12", 0x44, 0xC7, 2, "(Pr108) V/F5 (fifth frequency)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param152= 0, 6, "20 71 24 01 30 13", 0x44, 0xC7, 2, "(Pr109) V/F5 (fifth frequency voltage)", "Volt", "", 0, 10000, 0, 1, 1, 1, 0, , , , , 1; Param153= 0, 6, "20 71 24 01 30 14", 0x44, 0xC7, 2, "(Pr110) Third acceleration/deceleration time", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param154= 0, 6, "20 71 24 01 30 15", 0x44, 0xC7, 2, "(Pr111) Third deceleration time", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param155= 0, 6, "20 71 24 01 30 16", 0x44, 0xC7, 2, "(Pr112) Third torque boost", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param156= 0, 6, "20 71 24 01 30 17", 0x44, 0xC7, 2, "(Pr113) Third V/F(Base frequency)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param157= 0, 6, "20 71 24 01 30 18", 0x44, 0xC7, 2, "(Pr114) Third stall prevention operation current", "%", "", 0, 2200, 1500, 1, 1, 1, 0, , , , , 1; Param158= 0, 6, "20 71 24 01 30 19", 0x44, 0xC7, 2, "(Pr115) Third stall prevention operation frequency", "Hz", "", 0, 40000, 0, 1, 1, 1, 0, , , , , 2; Param159= 0, 6, "20 71 24 01 30 1A", 0x44, 0xC7, 2, "(Pr116) Third output frequency detection", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param160= 0, 6, "20 71 24 01 30 1B", 0x44, 0xC7, 2, "(Pr117) PU communication station", "", "", 0, 31, 0, 1, 1, 1, 0, , , , , 0; Param161= 0, 6, "20 71 24 01 30 1C", 0x44, 0xC7, 2, "(Pr118) PU communication speed", "", "", 48, 384, 192, 1, 1, 1, 0, , , , , 0; Param162= 0, 6, "20 71 24 01 30 1D", 0x44, 0xC7, 2, "(Pr119) PU communication stop bit length", "", "", 0, 11, 1, 1, 1, 1, 0, , , , , 0; Param163= 0, 6, "20 71 24 01 30 1E", 0x44, 0xC7, 2, "(Pr120) PU communication parity check", "", "", 0, 2, 2, 1, 1, 1, 0, , , , , 0; Param164= 0, 6, "20 71 24 01 30 1F", 0x44, 0xC7, 2, "(Pr121) Number of PU communication retries", "", "", 0, 65535, 1, 1, 1, 1, 0, , , , , 0; Param165= 0, 6, "20 71 24 01 30 20", 0x44, 0xC7, 2, "(Pr122) PU communication check time interval", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param166= 0, 6, "20 71 24 01 30 21", 0x44, 0xC7, 2, "(Pr123) PU communication waiting time setting", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param167= 0, 6, "20 71 24 01 30 22", 0x44, 0xC7, 2, "(Pr124) PU communication CR/LF presence/absence selection", "", "", 0, 2, 1, 1, 1, 1, 0, , , , , 0; Param168= 0, 6, "20 71 24 01 30 23", 0x44, 0xC7, 2, "(Pr125) Terminal 2 frequency setting gain frequency", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param169= 0, 6, "20 71 24 01 30 24", 0x44, 0xC7, 2, "(Pr126) Terminal 4 frequency setting gain frequency", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param170= 0, 6, "20 71 24 01 30 25", 0x44, 0xC7, 2, "(Pr127) PID control automatic switchover freqeuncy", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param171= 0, 6, "20 71 24 01 30 26", 0x44, 0xC7, 2, "(Pr128) PID action selection", "", "", 10, 61, 10, 1, 1, 1, 0, , , , , 0; Param172= 0, 6, "20 71 24 01 30 27", 0x44, 0xC7, 2, "(Pr129) PID proportional band", "%", "", 1, 65535, 1000, 1, 1, 1, 0, , , , , 1; Param173= 0, 6, "20 71 24 01 30 28", 0x44, 0xC7, 2, "(Pr130) PID integral time", "Sec", "", 1, 65535, 10, 1, 1, 1, 0, , , , , 1; Param174= 0, 6, "20 71 24 01 30 29", 0x44, 0xC7, 2, "(Pr131) PID upper limit", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param175= 0, 6, "20 71 24 01 30 2A", 0x44, 0xC7, 2, "(Pr132) PID lower limit", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param176= 0, 6, "20 71 24 01 30 2B", 0x44, 0xC7, 2, "(Pr133) PID action set point", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param177= 0, 6, "20 71 24 01 30 2C", 0x44, 0xC7, 2, "(Pr134) PID differential time", "Sec", "", 1, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param178= 0, 6, "20 71 24 01 30 2D", 0x44, 0xC7, 2, "(Pr135) Power-supply switchover sequence output terminal selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param179= 0, 6, "20 71 24 01 30 2E", 0x44, 0xC7, 2, "(Pr136) MC switchover interlock time", "Sec", "", 0, 1000, 10, 1, 1, 1, 0, , , , , 1; Param180= 0, 6, "20 71 24 01 30 2F", 0x44, 0xC7, 2, "(Pr137) Waiting time at a start", "Sec", "", 0, 1000, 5, 1, 1, 1, 0, , , , , 1; Param181= 0, 6, "20 71 24 01 30 30", 0x44, 0xC7, 2, "(Pr138) Commercial power-supply operation switchover selection at an alarm", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param182= 0, 6, "20 71 24 01 30 31", 0x44, 0xC7, 2, "(Pr139) Automatic switchover frequency between inverter and commercial power-supply operation", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param183= 0, 6, "20 71 24 01 30 32", 0x44, 0xC7, 2, "(Pr140) Backlash acceleration stopping frequency", "Hz", "", 0, 40000, 100, 1, 1, 1, 0, , , , , 2; Param184= 0, 6, "20 71 24 01 30 33", 0x44, 0xC7, 2, "(Pr141) Backlash acceleration stopping time", "Sec", "", 0, 3600, 5, 1, 1, 1, 0, , , , , 1; Param185= 0, 6, "20 71 24 01 30 34", 0x44, 0xC7, 2, "(Pr142) Backlash deceleration stopping frequency", "Hz", "", 0, 40000, 100, 1, 1, 1, 0, , , , , 2; Param186= 0, 6, "20 71 24 01 30 35", 0x44, 0xC7, 2, "(Pr143) Backlash deceleration stopping time", "Sec", "", 0, 3600, 5, 1, 1, 1, 0, , , , , 1; Param187= 0, 6, "20 71 24 01 30 36", 0x44, 0xC7, 2, "(Pr144) Speed setting switchover", "", "", 0, 110, 4, 1, 1, 1, 0, , , , , 0; Param188= 0, 6, "20 71 24 01 30 37", 0x44, 0xC7, 2, "(Pr145) PU display language selection", "", "", 0, 7, 0, 1, 1, 1, 0, , , , , 0; Param189= 0, 6, "20 71 24 01 30 3A", 0x44, 0xC7, 2, "(Pr148) Stall prevention level at 0V input", "%", "", 0, 2200, 1500, 1, 1, 1, 0, , , , , 1; Param190= 0, 6, "20 71 24 01 30 3B", 0x44, 0xC7, 2, "(Pr149) Stall prevention level at 10V input", "%", "", 0, 2200, 2000, 1, 1, 1, 0, , , , , 1; Param191= 0, 6, "20 71 24 01 30 3C", 0x44, 0xC7, 2, "(Pr150) Output current detection level", "%", "", 0, 2200, 1500, 1, 1, 1, 0, , , , , 1; Param192= 0, 6, "20 71 24 01 30 3D", 0x44, 0xC7, 2, "(Pr151) Output current detection signal delay time", "Sec", "", 0, 100, 0, 1, 1, 1, 0, , , , , 1; Param193= 0, 6, "20 71 24 01 30 3E", 0x44, 0xC7, 2, "(Pr152) Zero current detection level", "%", "", 0, 2200, 50, 1, 1, 1, 0, , , , , 1; Param194= 0, 6, "20 71 24 01 30 3F", 0x44, 0xC7, 2, "(Pr153) Zero current detection time", "Sec", "", 0, 100, 50, 1, 1, 1, 0, , , , , 2; Param195= 0, 6, "20 71 24 01 30 40", 0x44, 0xC7, 2, "(Pr154) Voltage reduction selection during stall prevention operation", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param196= 0, 6, "20 71 24 01 30 41", 0x44, 0xC7, 2, "(Pr155) RT signal reflection time selection", "", "", 0, 10, 0, 1, 1, 1, 0, , , , , 0; Param197= 0, 6, "20 71 24 01 30 42", 0x44, 0xC7, 2, "(Pr156) Stall prevention operation selection", "", "", 0, 101, 0, 1, 1, 1, 0, , , , , 0; Param198= 0, 6, "20 71 24 01 30 43", 0x44, 0xC7, 2, "(Pr157) OL signal output timer", "Sec", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param199= 0, 6, "20 71 24 01 30 44", 0x44, 0xC7, 2, "(Pr158) AM terminal function selection", "", "", 1, 53, 1, 1, 1, 1, 0, , , , , 0; Param200= 0, 6, "20 71 24 01 30 45", 0x44, 0xC7, 2, "(Pr159) Automatic switchover ON range between commercial power-supply and inverter operation", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param201= 0, 6, "20 71 24 01 30 46", 0x44, 0xC7, 2, "(Pr160) User group read selection", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param202= 0, 6, "20 71 24 01 30 47", 0x44, 0xC7, 2, "(Pr161) Frequency setting/key lock operation selection", "", "", 0, 11, 0, 1, 1, 1, 0, , , , , 0; Param203= 0, 6, "20 71 24 01 30 48", 0x44, 0xC7, 2, "(Pr162) Automatic restart after instantaneous power failure selection", "", "", 0, 12, 0, 1, 1, 1, 0, , , , , 0; Param204= 0, 6, "20 71 24 01 30 49", 0x44, 0xC7, 2, "(Pr163) First cushion time for restart", "Sec", "", 0, 200, 0, 1, 1, 1, 0, , , , , 1; Param205= 0, 6, "20 71 24 01 30 4A", 0x44, 0xC7, 2, "(Pr164) First cushion voltage for restart", "%", "", 0, 1000, 0, 1, 1, 1, 0, , , , , 1; Param206= 0, 6, "20 71 24 01 30 4B", 0x44, 0xC7, 2, "(Pr165) Stall prevention operation level for restart", "%", "", 0, 2200, 1500, 1, 1, 1, 0, , , , , 1; Param207= 0, 6, "20 71 24 01 30 4C", 0x44, 0xC7, 2, "(Pr166) Output current detection signal retention time", "Sec", "", 0, 65535, 1, 1, 1, 1, 0, , , , , 1; Param208= 0, 6, "20 71 24 01 30 4D", 0x44, 0xC7, 2, "(Pr167) Output current detection operation selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param209= 0, 6, "20 71 24 01 30 4E", 0x54, 0xC7, 2, "(Pr168) Parameters set by manufacturer", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param210= 0, 6, "20 71 24 01 30 4F", 0x54, 0xC7, 2, "(Pr169) Parameters set by manufacturer", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param211= 0, 6, "20 71 24 01 30 50", 0x44, 0xC7, 2, "(Pr170) Cumulative power meter clear", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param212= 0, 6, "20 71 24 01 30 51", 0x54, 0xC7, 2, "(Pr171) Operation hour meter clear", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param213= 0, 6, "20 71 24 01 30 52", 0x54, 0xC7, 2, "(Pr172) User group registered display/batch clear", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param214= 0, 6, "20 71 24 01 30 53", 0x54, 0xC7, 2, "(Pr173) User group registration", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param215= 0, 6, "20 71 24 01 30 54", 0x54, 0xC7, 2, "(Pr174) User group clear", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param216= 0, 6, "20 71 24 01 30 58", 0x44, 0xC7, 2, "(Pr178) STF terminal function selection", "", "", 0, 65535, 60, 1, 1, 1, 0, , , , , 0; Param217= 0, 6, "20 71 24 01 30 59", 0x44, 0xC7, 2, "(Pr179) STR terminal function selection", "", "", 0, 65535, 61, 1, 1, 1, 0, , , , , 0; Param218= 0, 6, "20 71 24 01 30 5A", 0x44, 0xC7, 2, "(Pr180) RL terminal function selection", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param219= 0, 6, "20 71 24 01 30 5B", 0x44, 0xC7, 2, "(Pr181) RM terminal function selection", "", "", 0, 65535, 1, 1, 1, 1, 0, , , , , 0; Param220= 0, 6, "20 71 24 01 30 5C", 0x44, 0xC7, 2, "(Pr182) RH terminal function selection", "", "", 0, 65535, 2, 1, 1, 1, 0, , , , , 0; Param221= 0, 6, "20 71 24 01 30 5D", 0x44, 0xC7, 2, "(Pr183) RT terminal function selection", "", "", 0, 65535, 3, 1, 1, 1, 0, , , , , 0; Param222= 0, 6, "20 71 24 01 30 5E", 0x44, 0xC7, 2, "(Pr184) AU terminal function selection", "", "", 0, 65535, 4, 1, 1, 1, 0, , , , , 0; Param223= 0, 6, "20 71 24 01 30 5F", 0x44, 0xC7, 2, "(Pr185) JOG terminal function selection", "", "", 0, 65535, 5, 1, 1, 1, 0, , , , , 0; Param224= 0, 6, "20 71 24 01 30 60", 0x44, 0xC7, 2, "(Pr186) CS terminal function selection", "", "", 0, 65535, 6, 1, 1, 1, 0, , , , , 0; Param225= 0, 6, "20 71 24 01 30 61", 0x44, 0xC7, 2, "(Pr187) MRS terminal function selection", "", "", 0, 65535, 24, 1, 1, 1, 0, , , , , 0; Param226= 0, 6, "20 71 24 01 30 62", 0x44, 0xC7, 2, "(Pr188) STOP terminal function selection", "", "", 0, 65535, 25, 1, 1, 1, 0, , , , , 0; Param227= 0, 6, "20 71 24 01 30 63", 0x44, 0xC7, 2, "(Pr189) RES terminal function selection", "", "", 0, 65535, 62, 1, 1, 1, 0, , , , , 0; Param228= 0, 6, "20 71 24 01 30 64", 0x44, 0xC7, 2, "(Pr190) RUN terminal function selection", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param229= 0, 6, "20 71 24 01 30 65", 0x44, 0xC7, 2, "(Pr191) SU terminal function selection", "", "", 0, 65535, 1, 1, 1, 1, 0, , , , , 0; Param230= 0, 6, "20 71 24 01 30 66", 0x44, 0xC7, 2, "(Pr192) IPF terminal function selection", "", "", 0, 65535, 2, 1, 1, 1, 0, , , , , 0; Param231= 0, 6, "20 71 24 01 30 67", 0x44, 0xC7, 2, "(Pr193) OL terminal function selection", "", "", 0, 65535, 3, 1, 1, 1, 0, , , , , 0; Param232= 0, 6, "20 71 24 01 30 68", 0x44, 0xC7, 2, "(Pr194) FU terminal function selection", "", "", 0, 65535, 4, 1, 1, 1, 0, , , , , 0; Param233= 0, 6, "20 71 24 01 30 69", 0x44, 0xC7, 2, "(Pr195) ABC1 terminal function selection", "", "", 0, 65535, 99, 1, 1, 1, 0, , , , , 0; Param234= 0, 6, "20 71 24 01 30 6A", 0x44, 0xC7, 2, "(Pr196) ABC2 terminal function selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param235= 0, 6, "20 72 24 01 30 2A", 0x44, 0xC7, 2, "(Pr232) Multi-speed setting(speed 8)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param236= 0, 6, "20 72 24 01 30 2B", 0x44, 0xC7, 2, "(Pr233) Multi-speed setting(speed 9)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param237= 0, 6, "20 72 24 01 30 2C", 0x44, 0xC7, 2, "(Pr234) Multi-speed setting(speed 10)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param238= 0, 6, "20 72 24 01 30 2D", 0x44, 0xC7, 2, "(Pr235) Multi-speed setting(speed 11)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param239= 0, 6, "20 72 24 01 30 2E", 0x44, 0xC7, 2, "(Pr236) Multi-speed setting(speed 12)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param240= 0, 6, "20 72 24 01 30 2F", 0x44, 0xC7, 2, "(Pr237) Multi-speed setting(speed 13)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param241= 0, 6, "20 72 24 01 30 30", 0x44, 0xC7, 2, "(Pr238) Multi-speed setting(speed 14)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param242= 0, 6, "20 72 24 01 30 31", 0x44, 0xC7, 2, "(Pr239) Multi-speed setting(speed 15)", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param243= 0, 6, "20 72 24 01 30 32", 0x44, 0xC7, 2, "(Pr240) Soft-PWM operation selection", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param244= 0, 6, "20 72 24 01 30 33", 0x44, 0xC7, 2, "(Pr241) Analog input display unit switchover", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param245= 0, 6, "20 72 24 01 30 34", 0x44, 0xC7, 2, "(Pr242) Terminal 1 added compensation amount (terminal 2)", "%", "", 0, 1000, 1000, 1, 1, 1, 0, , , , , 1; Param246= 0, 6, "20 72 24 01 30 35", 0x44, 0xC7, 2, "(Pr243) Terminal 1 added compensation amount (terminal 4)", "%", "", 0, 1000, 750, 1, 1, 1, 0, , , , , 1; Param247= 0, 6, "20 72 24 01 30 36", 0x44, 0xC7, 2, "(Pr244) Cooling fan operation selection", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param248= 0, 6, "20 72 24 01 30 37", 0x44, 0xC7, 2, "(Pr245) Rated slip", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param249= 0, 6, "20 72 24 01 30 38", 0x44, 0xC7, 2, "(Pr246) Slip compensation time constant", "Sec", "", 1, 1000, 50, 1, 1, 1, 0, , , , , 2; Param250= 0, 6, "20 72 24 01 30 39", 0x44, 0xC7, 2, "(Pr247) Constant-output region slip compensation selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param251= 0, 6, "20 72 24 01 30 3C", 0x44, 0xC7, 2, "(Pr250) Stop selection", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param252= 0, 6, "20 72 24 01 30 3D", 0x44, 0xC7, 2, "(Pr251) Output phase failure protection selection", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param253= 0, 6, "20 72 24 01 30 3E", 0x44, 0xC7, 2, "(Pr252) Override bias", "%", "", 0, 2000, 500, 1, 1, 1, 0, , , , , 1; Param254= 0, 6, "20 72 24 01 30 3F", 0x44, 0xC7, 2, "(Pr253) Override gain", "%", "", 0, 2000, 1500, 1, 1, 1, 0, , , , , 1; Param255= 0, 6, "20 72 24 01 30 41", 0x54, 0xC7, 2, "(Pr255) Life alarm status display", "", "", 0, 15, 0, 1, 1, 1, 0, , , , , 0; Param256= 0, 6, "20 72 24 01 30 42", 0x54, 0xC7, 2, "(Pr256) Inrush current suppression circuit life display", "%", "", 0, 100, 100, 1, 1, 1, 0, , , , , 0; Param257= 0, 6, "20 72 24 01 30 43", 0x54, 0xC7, 2, "(Pr257) Control circuit capacitor life display", "%", "", 0, 100, 100, 1, 1, 1, 0, , , , , 0; Param258= 0, 6, "20 72 24 01 30 44", 0x54, 0xC7, 2, "(Pr258) Main circuit capacitor life display", "%", "", 0, 100, 100, 1, 1, 1, 0, , , , , 0; Param259= 0, 6, "20 72 24 01 30 45", 0x44, 0xC7, 2, "(Pr259) Main circuit capacitor life measuring", "", "", 0, 103, 0, 1, 1, 1, 0, , , , , 0; Param260= 0, 6, "20 72 24 01 30 47", 0x44, 0xC7, 2, "(Pr261) Power failure stop selection", "", "", 0, 12, 0, 1, 1, 1, 0, , , , , 0; Param261= 0, 6, "20 72 24 01 30 48", 0x44, 0xC7, 2, "(Pr262) Subtracted frequency at deceleration start", "Hz", "", 0, 2000, 300, 1, 1, 1, 0, , , , , 2; Param262= 0, 6, "20 72 24 01 30 49", 0x44, 0xC7, 2, "(Pr263) Subtraction starting frequency", "Hz", "", 0, 65535, 6000, 1, 1, 1, 0, , , , , 2; Param263= 0, 6, "20 72 24 01 30 4A", 0x44, 0xC7, 2, "(Pr264) Power-failure deceleration time 1", "Sec", "", 0, 36000, 50, 1, 1, 1, 0, , , , , 1; Param264= 0, 6, "20 72 24 01 30 4B", 0x44, 0xC7, 2, "(Pr265) Power-failure deceleration time 2", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param265= 0, 6, "20 72 24 01 30 4C", 0x44, 0xC7, 2, "(Pr266) Power failure deceleration time switchover frequency", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param266= 0, 6, "20 72 24 01 30 4D", 0x44, 0xC7, 2, "(Pr267) Terminal 4 input selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param267= 0, 6, "20 72 24 01 30 4E", 0x44, 0xC7, 2, "(Pr268) Monitor decimal digits selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param268= 0, 6, "20 72 24 01 30 50", 0x44, 0xC7, 2, "(Pr270) Stop-on-contact/load torque high-speed frequency control selection", "", "", 0, 3, 0, 1, 1, 1, 0, , , , , 0; Param269= 0, 6, "20 72 24 01 30 51", 0x44, 0xC7, 2, "(Pr271) High-speed setting maximum current", "%", "", 0, 2200, 500, 1, 1, 1, 0, , , , , 1; Param270= 0, 6, "20 72 24 01 30 52", 0x44, 0xC7, 2, "(Pr272) Mid-speed setting maximum current", "%", "", 0, 2200, 1000, 1, 1, 1, 0, , , , , 1; Param271= 0, 6, "20 72 24 01 30 53", 0x44, 0xC7, 2, "(Pr273) Current averaging range", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param272= 0, 6, "20 72 24 01 30 54", 0x44, 0xC7, 2, "(Pr274) Current averaging filter constant", "", "", 1, 4000, 16, 1, 1, 1, 0, , , , , 0; Param273= 0, 6, "20 72 24 01 30 55", 0x44, 0xC7, 2, "(Pr275) Stop-on-contact excitation current low-speed multiplying factor", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param274= 0, 6, "20 72 24 01 30 56", 0x44, 0xC7, 2, "(Pr276) Stop-on-contact PWM carrier frequency", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param275= 0, 6, "20 72 24 01 30 58", 0x44, 0xC7, 2, "(Pr278) Brake opening frequency", "Hz", "", 0, 3000, 300, 1, 1, 1, 0, , , , , 2; Param276= 0, 6, "20 72 24 01 30 59", 0x44, 0xC7, 2, "(Pr279) Brake opening current", "%", "", 0, 2200, 1300, 1, 1, 1, 0, , , , , 1; Param277= 0, 6, "20 72 24 01 30 5A", 0x44, 0xC7, 2, "(Pr280) Brake opening current detection time", "Sec", "", 0, 20, 3, 1, 1, 1, 0, , , , , 1; Param278= 0, 6, "20 72 24 01 30 5B", 0x44, 0xC7, 2, "(Pr281) Brake operation time at start", "Sec", "", 0, 50, 3, 1, 1, 1, 0, , , , , 1; Param279= 0, 6, "20 72 24 01 30 5C", 0x44, 0xC7, 2, "(Pr282) Brake operation frequency", "Hz", "", 0, 3000, 600, 1, 1, 1, 0, , , , , 2; Param280= 0, 6, "20 72 24 01 30 5D", 0x44, 0xC7, 2, "(Pr283) Brake operation time at stop", "Sec", "", 0, 50, 3, 1, 1, 1, 0, , , , , 1; Param281= 0, 6, "20 72 24 01 30 5E", 0x44, 0xC7, 2, "(Pr284) Deceleration detection function selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param282= 0, 6, "20 72 24 01 30 5F", 0x44, 0xC7, 2, "(Pr285) Overspeed detection frequency", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param283= 0, 6, "20 72 24 01 30 60", 0x44, 0xC7, 2, "(Pr286) Droop gain", "%", "", 0, 1000, 0, 1, 1, 1, 0, , , , , 1; Param284= 0, 6, "20 72 24 01 30 61", 0x44, 0xC7, 2, "(Pr287) Droop filter D429", "Sec", "", 0, 100, 30, 1, 1, 1, 0, , , , , 2; Param285= 0, 6, "20 72 24 01 30 62", 0x44, 0xC7, 2, "(Pr288) Droop function activation selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param286= 0, 6, "20 72 24 01 30 65", 0x44, 0xC7, 2, "(Pr291) Pulse input and output selection", "", "", 0, 100, 0, 1, 1, 1, 0, , , , , 0; Param287= 0, 6, "20 72 24 01 30 66", 0x44, 0xC7, 2, "(Pr292) Automatic acceleration and deceleration", "", "", 0, 11, 0, 1, 1, 1, 0, , , , , 0; Param288= 0, 6, "20 72 24 01 30 67", 0x44, 0xC7, 2, "(Pr293) Acceleration and deceleration valid selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param289= 0, 6, "20 72 24 01 30 68", 0x44, 0xC7, 2, "(Pr294) UV-avoidance voltage gain", "%", "", 0, 2000, 1000, 1, 1, 1, 0, , , , , 1; Param290= 0, 6, "20 72 24 01 30 6D", 0x44, 0xC7, 2, "(Pr299) Rotation direction detection selection at restarting", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param291= 0, 6, "20 73 24 01 30 0A", 0x44, 0xC7, 2, "(Pr300) BCD input bias", "Hz", "", 0, 40000, 0, 1, 1, 1, 0, , , , , 2; Param292= 0, 6, "20 73 24 01 30 0B", 0x44, 0xC7, 2, "(Pr301) BCD input gain", "Hz", "", 0, 65535, 6000, 1, 1, 1, 0, , , , , 2; Param293= 0, 6, "20 73 24 01 30 0C", 0x44, 0xC7, 2, "(Pr302) BIN input bias", "Hz", "", 0, 40000, 0, 1, 1, 1, 0, , , , , 2; Param294= 0, 6, "20 73 24 01 30 0D", 0x44, 0xC7, 2, "(Pr303) BIN input gain", "Hz", "", 0, 65535, 6000, 1, 1, 1, 0, , , , , 2; Param295= 0, 6, "20 73 24 01 30 0E", 0x44, 0xC7, 2, "(Pr304) Digital input and analog input compensation enable/disable selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param296= 0, 6, "20 73 24 01 30 0F", 0x44, 0xC7, 2, "(Pr305) Read timing operation selection", "", "", 0, 10, 0, 1, 1, 1, 0, , , , , 0; Param297= 0, 6, "20 73 24 01 30 10", 0x44, 0xC7, 2, "(Pr306) Analog output signal selection", "", "", 1, 53, 2, 1, 1, 1, 0, , , , , 0; Param298= 0, 6, "20 73 24 01 30 11", 0x44, 0xC7, 2, "(Pr307) Setting for zero analog output", "%", "", 0, 1000, 0, 1, 1, 1, 0, , , , , 1; Param299= 0, 6, "20 73 24 01 30 12", 0x44, 0xC7, 2, "(Pr308) Setting for maximum analog output", "%", "", 0, 1000, 1000, 1, 1, 1, 0, , , , , 1; Param300= 0, 6, "20 73 24 01 30 13", 0x44, 0xC7, 2, "(Pr309) Analog output signal voltage/current switchover", "", "", 0, 11, 0, 1, 1, 1, 0, , , , , 0; Param301= 0, 6, "20 73 24 01 30 14", 0x44, 0xC7, 2, "(Pr310) Analog meter voltage output selection", "", "", 1, 53, 2, 1, 1, 1, 0, , , , , 0; Param302= 0, 6, "20 73 24 01 30 15", 0x44, 0xC7, 2, "(Pr311) Setting for zero analog meter voltage output", "%", "", 0, 1000, 0, 1, 1, 1, 0, , , , , 1; Param303= 0, 6, "20 73 24 01 30 16", 0x44, 0xC7, 2, "(Pr312) Setting for maximum analog meter voltage output", "%", "", 0, 1000, 1000, 1, 1, 1, 0, , , , , 1; Param304= 0, 6, "20 73 24 01 30 17", 0x44, 0xC7, 2, "(Pr313) DO0 output selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param305= 0, 6, "20 73 24 01 30 18", 0x44, 0xC7, 2, "(Pr314) DO1 output selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param306= 0, 6, "20 73 24 01 30 19", 0x44, 0xC7, 2, "(Pr315) DO2 output selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param307= 0, 6, "20 73 24 01 30 1A", 0x44, 0xC7, 2, "(Pr316) DO3 output selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param308= 0, 6, "20 73 24 01 30 1B", 0x44, 0xC7, 2, "(Pr317) DO4 output selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param309= 0, 6, "20 73 24 01 30 1C", 0x44, 0xC7, 2, "(Pr318) DO5 output selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param310= 0, 6, "20 73 24 01 30 1D", 0x44, 0xC7, 2, "(Pr319) DO6 output selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param311= 0, 6, "20 73 24 01 30 1E", 0x44, 0xC7, 2, "(Pr320) RA1 output selection", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param312= 0, 6, "20 73 24 01 30 1F", 0x44, 0xC7, 2, "(Pr321) RA2 output selection", "", "", 0, 65535, 1, 1, 1, 1, 0, , , , , 0; Param313= 0, 6, "20 73 24 01 30 20", 0x44, 0xC7, 2, "(Pr322) RA3 output selection", "", "", 0, 65535, 2, 1, 1, 1, 0, , , , , 0; Param314= 0, 6, "20 73 24 01 30 21", 0x44, 0xC7, 2, "(Pr323) AM0 0V adjustment", "%", "", 900, 1100, 1000, 1, 1, 1, 0, , , , , 0; Param315= 0, 6, "20 73 24 01 30 22", 0x44, 0xC7, 2, "(Pr324) AM1 0mA adjustment", "%", "", 900, 1100, 1000, 1, 1, 1, 0, , , , , 0; Param316= 0, 6, "20 73 24 01 30 27", 0x44, 0xC7, 2, "(Pr329) Digital input unit selection", "", "", 0, 3, 1, 1, 1, 1, 0, , , , , 0; Param317= 0, 6, "20 73 24 01 30 29", 0x44, 0xC7, 2, "(Pr331) RS-485 communication station", "", "", 0, 247, 0, 1, 1, 1, 0, , , , , 0; Param318= 0, 6, "20 73 24 01 30 2A", 0x44, 0xC7, 2, "(Pr332) RS-485 communication speed", "", "", 3, 384, 96, 1, 1, 1, 0, , , , , 0; Param319= 0, 6, "20 73 24 01 30 2B", 0x44, 0xC7, 2, "(Pr333) RS-485 communication stop bit length", "", "", 0, 11, 1, 1, 1, 1, 0, , , , , 0; Param320= 0, 6, "20 73 24 01 30 2C", 0x44, 0xC7, 2, "(Pr334) RS-485 communication parity@check selection", "", "", 0, 2, 2, 1, 1, 1, 0, , , , , 0; Param321= 0, 6, "20 73 24 01 30 2D", 0x44, 0xC7, 2, "(Pr335) RS-485 communication@number of retries", "", "", 0, 65535, 1, 1, 1, 1, 0, , , , , 0; Param322= 0, 6, "20 73 24 01 30 2E", 0x44, 0xC7, 2, "(Pr336) RS-485 communication check time interva", "Sec", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 1; Param323= 0, 6, "20 73 24 01 30 2F", 0x44, 0xC7, 2, "(Pr337) RS-485 communication waiting time setting", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param324= 0, 6, "20 73 24 01 30 30", 0x44, 0xC7, 2, "(Pr338) Communication operation command source", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param325= 0, 6, "20 73 24 01 30 31", 0x44, 0xC7, 2, "(Pr339) Communication speed command source", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param326= 0, 6, "20 73 24 01 30 32", 0x44, 0xC7, 2, "(Pr340) Communication startup mode selection", "", "", 0, 12, 0, 1, 1, 1, 0, , , , , 0; Param327= 0, 6, "20 73 24 01 30 33", 0x44, 0xC7, 2, "(Pr341) RS-485 communication CR/LF selection", "", "", 0, 2, 1, 1, 1, 1, 0, , , , , 0; Param328= 0, 6, "20 73 24 01 30 34", 0x44, 0xC7, 2, "(Pr342) Communication EEPROM write selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param329= 0, 6, "20 73 24 01 30 35", 0x54, 0xC7, 2, "(Pr343) Communication error count", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param330= 0, 6, "20 73 24 01 30 37", 0x44, 0xC7, 2, "(Pr345) DeviceNet Address", "", "", 0, 4095, 63, 1, 1, 1, 0, , , , , 0; Param331= 0, 6, "20 73 24 01 30 38", 0x44, 0xC7, 2, "(Pr346) DeviceNet Configuration", "", "", 0, 4095, 132, 1, 1, 1, 0, , , , , 0; Param332= 0, 6, "20 73 24 01 30 3B", 0x44, 0xC7, 2, "(Pr349) Communication reset selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param333= 0, 6, "20 73 24 01 30 3C", 0x44, 0xC7, 2, "(Pr350) Stop position command selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param334= 0, 6, "20 73 24 01 30 3D", 0x44, 0xC7, 2, "(Pr351) Orientation switchover speed", "Hz", "", 0, 3000, 200, 1, 1, 1, 0, , , , , 2; Param335= 0, 6, "20 73 24 01 30 3E", 0x44, 0xC7, 2, "(Pr352) Creep speed", "Hz", "", 0, 1000, 50, 1, 1, 1, 0, , , , , 2; Param336= 0, 6, "20 73 24 01 30 3F", 0x44, 0xC7, 2, "(Pr353) Creep select position", "", "", 0, 16383, 511, 1, 1, 1, 0, , , , , 0; Param337= 0, 6, "20 73 24 01 30 40", 0x44, 0xC7, 2, "(Pr354) Position loop select position", "", "", 0, 8191, 96, 1, 1, 1, 0, , , , , 0; Param338= 0, 6, "20 73 24 01 30 41", 0x44, 0xC7, 2, "(Pr355) DC injection brake start position", "", "", 0, 255, 5, 1, 1, 1, 0, , , , , 0; Param339= 0, 6, "20 73 24 01 30 42", 0x44, 0xC7, 2, "(Pr356) Internal stop position command", "", "", 0, 16383, 0, 1, 1, 1, 0, , , , , 0; Param340= 0, 6, "20 73 24 01 30 43", 0x44, 0xC7, 2, "(Pr357) In-position zone", "", "", 0, 255, 5, 1, 1, 1, 0, , , , , 0; Param341= 0, 6, "20 73 24 01 30 44", 0x44, 0xC7, 2, "(Pr358) Servo torque selection", "", "", 0, 13, 1, 1, 1, 1, 0, , , , , 0; Param342= 0, 6, "20 73 24 01 30 45", 0x44, 0xC7, 2, "(Pr359) Encoder rotation direction", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param343= 0, 6, "20 73 24 01 30 46", 0x44, 0xC7, 2, "(Pr360) 12-bit data selection", "", "", 0, 127, 0, 1, 1, 1, 0, , , , , 0; Param344= 0, 6, "20 73 24 01 30 47", 0x44, 0xC7, 2, "(Pr361) Position shift", "", "", 0, 16383, 0, 1, 1, 1, 0, , , , , 0; Param345= 0, 6, "20 73 24 01 30 48", 0x44, 0xC7, 2, "(Pr362) Orientation position loop gain", "", "", 1, 10, 1, 1, 1, 1, 0, , , , , 0; Param346= 0, 6, "20 73 24 01 30 49", 0x44, 0xC7, 2, "(Pr363) In-position signal output delay time", "Sec", "", 0, 50, 5, 1, 1, 1, 0, , , , , 1; Param347= 0, 6, "20 73 24 01 30 4A", 0x44, 0xC7, 2, "(Pr364) Encoder stop check time", "Sec", "", 0, 50, 5, 1, 1, 1, 0, , , , , 1; Param348= 0, 6, "20 73 24 01 30 4B", 0x44, 0xC7, 2, "(Pr365) Orientation time limit", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param349= 0, 6, "20 73 24 01 30 4C", 0x44, 0xC7, 2, "(Pr366) Recheck time", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param350= 0, 6, "20 73 24 01 30 4D", 0x44, 0xC7, 2, "(Pr367) Speed feedback range", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param351= 0, 6, "20 73 24 01 30 4E", 0x44, 0xC7, 2, "(Pr368) Feedback gain", "", "", 0, 1000, 10, 1, 1, 1, 0, , , , , 1; Param352= 0, 6, "20 73 24 01 30 4F", 0x44, 0xC7, 2, "(Pr369) Number of encoder pulses", "", "", 0, 4096, 1024, 1, 1, 1, 0, , , , , 0; Param353= 0, 6, "20 73 24 01 30 54", 0x44, 0xC7, 2, "(Pr374) Overspeed detection level", "Hz", "", 0, 40000, 14000, 1, 1, 1, 0, , , , , 2; Param354= 0, 6, "20 73 24 01 30 56", 0x44, 0xC7, 2, "(Pr376) Break in the cable detection enable/disable selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param355= 0, 6, "20 73 24 01 30 5A", 0x44, 0xC7, 2, "(Pr380) Acceleration S pattern 1", "%", "", 0, 50, 0, 1, 1, 1, 0, , , , , 0; Param356= 0, 6, "20 73 24 01 30 5B", 0x44, 0xC7, 2, "(Pr381) Deceleration S pattern 1", "%", "", 0, 50, 0, 1, 1, 1, 0, , , , , 0; Param357= 0, 6, "20 73 24 01 30 5C", 0x44, 0xC7, 2, "(Pr382) Acceleration S pattern 2", "%", "", 0, 50, 0, 1, 1, 1, 0, , , , , 0; Param358= 0, 6, "20 73 24 01 30 5D", 0x44, 0xC7, 2, "(Pr383) Deceleration S pattern 2", "%", "", 0, 50, 0, 1, 1, 1, 0, , , , , 0; Param359= 0, 6, "20 73 24 01 30 5E", 0x44, 0xC7, 2, "(Pr384) Input pulse frequency division ratio", "", "", 0, 250, 0, 1, 1, 1, 0, , , , , 0; Param360= 0, 6, "20 73 24 01 30 5F", 0x44, 0xC7, 2, "(Pr385) Zero-input pulse frequency", "Hz", "", 0, 40000, 0, 1, 1, 1, 0, , , , , 2; Param361= 0, 6, "20 73 24 01 30 60", 0x44, 0xC7, 2, "(Pr386) Maximum-input pulse frequency", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param362= 0, 6, "20 74 24 01 30 1D", 0x44, 0xC7, 2, "(Pr419) Position command source selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param363= 0, 6, "20 74 24 01 30 1E", 0x44, 0xC7, 2, "(Pr420) Command pulse scaling factor numerator", "", "", 0, 32767, 1, 1, 1, 1, 0, , , , , 0; Param364= 0, 6, "20 74 24 01 30 1F", 0x44, 0xC7, 2, "(Pr421) Command pulse scaling factor denominator", "", "", 0, 32767, 1, 1, 1, 1, 0, , , , , 0; Param365= 0, 6, "20 74 24 01 30 20", 0x44, 0xC7, 2, "(Pr422) Position loop gain", "Sec", "", 0, 150, 25, 1, 1, 1, 0, , , , , 0; Param366= 0, 6, "20 74 24 01 30 21", 0x44, 0xC7, 2, "(Pr423) Position feed forward gain", "%", "", 0, 100, 0, 1, 1, 1, 0, , , , , 0; Param367= 0, 6, "20 74 24 01 30 22", 0x44, 0xC7, 2, "(Pr424) Position command acceleration/deceleration time constant", "Sec", "", 0, 50000, 0, 1, 1, 1, 0, , , , , 3; Param368= 0, 6, "20 74 24 01 30 23", 0x44, 0xC7, 2, "(Pr425) Position feed forward command filter", "Sec", "", 0, 5000, 0, 1, 1, 1, 0, , , , , 3; Param369= 0, 6, "20 74 24 01 30 24", 0x44, 0xC7, 2, "(Pr426) In-position width", "", "", 0, 32767, 100, 1, 1, 1, 0, , , , , 0; Param370= 0, 6, "20 74 24 01 30 25", 0x44, 0xC7, 2, "(Pr427) Excessive level error", "", "", 0, 65535, 40, 1, 1, 1, 0, , , , , 0; Param371= 0, 6, "20 74 24 01 30 26", 0x44, 0xC7, 2, "(Pr428) Positioning option selection", "", "", 0, 5, 0, 1, 1, 1, 0, , , , , 0; Param372= 0, 6, "20 74 24 01 30 27", 0x44, 0xC7, 2, "(Pr429) Clear signal selection", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param373= 0, 6, "20 74 24 01 30 28", 0x44, 0xC7, 2, "(Pr430) Pulse monitor selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param374= 0, 6, "20 74 24 01 30 39", 0x44, 0xC7, 2, "(Pr447) Digital torque operation bias", "%", "", 0, 400, 0, 1, 1, 1, 0, , , , , 0; Param375= 0, 6, "20 74 24 01 30 3A", 0x44, 0xC7, 2, "(Pr448) Digital torque operation gain", "%", "", 0, 65535, 150, 1, 1, 1, 0, , , , , 0; Param376= 0, 6, "20 74 24 01 30 3C", 0x44, 0xC7, 2, "(Pr450) Second applied motor", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param377= 0, 6, "20 74 24 01 30 3D", 0x44, 0xC7, 2, "(Pr451) Second motor control method selection", "", "", 10, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param378= 0, 6, "20 74 24 01 30 40", 0x44, 0xC7, 2, "(Pr454) Number of second motor poles", "", "", 2, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param379= 0, 6, "20 74 24 01 30 42", 0x44, 0xC7, 2, "(Pr456) Second rated motor voltage", "Volt", "", 0, 10000, 2000, 1, 1, 1, 0, , , , , 1; Param380= 0, 6, "20 74 24 01 30 43", 0x44, 0xC7, 2, "(Pr457) Second rated motor frequency", "Hz", "", 5000, 12000, 6000, 1, 1, 1, 0, , , , , 2; Param381= 0, 6, "20 74 24 01 30 49", 0x44, 0xC7, 2, "(Pr463) Second motor auto-tuning setting/status", "", "", 0, 101, 0, 1, 1, 1, 0, , , , , 0; Param382= 0, 6, "20 74 24 01 30 4A", 0x44, 0xC7, 2, "(Pr464) Digital position control sudden stop deceleration time", "", "", 0, 360, 0, 1, 1, 1, 0, , , , , 0; Param383= 0, 6, "20 74 24 01 30 4B", 0x44, 0xC7, 2, "(Pr465) First position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param384= 0, 6, "20 74 24 01 30 4C", 0x44, 0xC7, 2, "(Pr466) First position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param385= 0, 6, "20 74 24 01 30 4D", 0x44, 0xC7, 2, "(Pr467) Second position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param386= 0, 6, "20 74 24 01 30 4E", 0x44, 0xC7, 2, "(Pr468) Second position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param387= 0, 6, "20 74 24 01 30 4F", 0x44, 0xC7, 2, "(Pr469) Third position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param388= 0, 6, "20 74 24 01 30 50", 0x44, 0xC7, 2, "(Pr470) Third position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param389= 0, 6, "20 74 24 01 30 51", 0x44, 0xC7, 2, "(Pr471) Fourth position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param390= 0, 6, "20 74 24 01 30 52", 0x44, 0xC7, 2, "(Pr472) Fourth position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param391= 0, 6, "20 74 24 01 30 53", 0x44, 0xC7, 2, "(Pr473) Fifth position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param392= 0, 6, "20 74 24 01 30 54", 0x44, 0xC7, 2, "(Pr474) Fifth position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param393= 0, 6, "20 74 24 01 30 55", 0x44, 0xC7, 2, "(Pr475) Sixth position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param394= 0, 6, "20 74 24 01 30 56", 0x44, 0xC7, 2, "(Pr476) Sixth position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param395= 0, 6, "20 74 24 01 30 57", 0x44, 0xC7, 2, "(Pr477) Seventh position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param396= 0, 6, "20 74 24 01 30 58", 0x44, 0xC7, 2, "(Pr478) Seventh position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param397= 0, 6, "20 74 24 01 30 59", 0x44, 0xC7, 2, "(Pr479) Eighth position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param398= 0, 6, "20 74 24 01 30 5A", 0x44, 0xC7, 2, "(Pr480) Eighth position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param399= 0, 6, "20 74 24 01 30 5B", 0x44, 0xC7, 2, "(Pr481) Ninth position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param400= 0, 6, "20 74 24 01 30 5C", 0x44, 0xC7, 2, "(Pr482) Ninth position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param401= 0, 6, "20 74 24 01 30 5D", 0x44, 0xC7, 2, "(Pr483) Tenth position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param402= 0, 6, "20 74 24 01 30 5E", 0x44, 0xC7, 2, "(Pr484) Tenth position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param403= 0, 6, "20 74 24 01 30 5F", 0x44, 0xC7, 2, "(Pr485) Eleventh position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param404= 0, 6, "20 74 24 01 30 60", 0x44, 0xC7, 2, "(Pr486) Eleventh position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param405= 0, 6, "20 74 24 01 30 61", 0x44, 0xC7, 2, "(Pr487) Twelfth position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param406= 0, 6, "20 74 24 01 30 62", 0x44, 0xC7, 2, "(Pr488) Twelfth position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param407= 0, 6, "20 74 24 01 30 63", 0x44, 0xC7, 2, "(Pr489) Thirteenth position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param408= 0, 6, "20 74 24 01 30 64", 0x44, 0xC7, 2, "(Pr490) Thirteenth position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param409= 0, 6, "20 74 24 01 30 65", 0x44, 0xC7, 2, "(Pr491) Fourteenth position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param410= 0, 6, "20 74 24 01 30 66", 0x44, 0xC7, 2, "(Pr492) Fourteenth position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param411= 0, 6, "20 74 24 01 30 67", 0x44, 0xC7, 2, "(Pr493) Fifteenth position feed amount lower 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param412= 0, 6, "20 74 24 01 30 68", 0x44, 0xC7, 2, "(Pr494) Fifteenth position feed amount upper 4 digits", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param413= 0, 6, "20 74 24 01 30 69", 0x44, 0xC7, 2, "(Pr495) Remote output selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param414= 0, 6, "20 74 24 01 30 6A", 0x44, 0xC7, 2, "(Pr496) Remote output data 1", "", "", 0, 4095, 0, 1, 1, 1, 0, , , , , 0; Param415= 0, 6, "20 74 24 01 30 6B", 0x44, 0xC7, 2, "(Pr497) Remote output data 2", "", "", 0, 4095, 0, 1, 1, 1, 0, , , , , 0; Param416= 0, 6, "20 75 24 01 30 0A", 0x44, 0xC7, 2, "(Pr500) Communication error execution waiting time", "Sec", "", 0, 9998, 0, 1, 1, 1, 0, , , , , 1; Param417= 0, 6, "20 75 24 01 30 0B", 0x44, 0xC7, 2, "(Pr501) Communication error occurrence count display", "", "", 0, 0, 0, 1, 1, 1, 0, , , , , 0; Param418= 0, 6, "20 75 24 01 30 0C", 0x44, 0xC7, 2, "(Pr502) Stop mode selection at communication error", "", "", 0, 3, 0, 1, 1, 1, 0, , , , , 0; Param419= 0, 6, "20 75 24 01 30 0D", 0x44, 0xC7, 2, "(Pr503) Maintenance timer", "", "", 0, 9998, 0, 1, 1, 1, 0, , , , , 0; Param420= 0, 6, "20 75 24 01 30 0E", 0x44, 0xC7, 2, "(Pr504) Maintenance timer alarm output set time", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param421= 0, 6, "20 75 24 01 30 1A", 0x44, 0xC7, 2, "(Pr516) S-curve time of acceleration start", "Sec", "", 1, 25, 1, 1, 1, 1, 0, , , , , 1; Param422= 0, 6, "20 75 24 01 30 1B", 0x44, 0xC7, 2, "(Pr517) S-curve time of acceleration end", "Sec", "", 1, 25, 1, 1, 1, 1, 0, , , , , 1; Param423= 0, 6, "20 75 24 01 30 1C", 0x44, 0xC7, 2, "(Pr518) S-curve time of deceleration start", "Sec", "", 1, 25, 1, 1, 1, 1, 0, , , , , 1; Param424= 0, 6, "20 75 24 01 30 1D", 0x44, 0xC7, 2, "(Pr519) S-curve time of deceleration end", "Sec", "", 1, 25, 1, 1, 1, 1, 0, , , , , 1; Param425= 0, 6, "20 75 24 01 30 39", 0x44, 0xC7, 2, "(Pr547) USB communication number", "", "", 0, 31, 0, 1, 1, 1, 0, , , , , 0; Param426= 0, 6, "20 75 24 01 30 3A", 0x44, 0xC7, 2, "(Pr548) USB communication check interval time", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param427= 0, 6, "20 75 24 01 30 3B", 0x44, 0xC7, 2, "(Pr549) Protocol selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param428= 0, 6, "20 75 24 01 30 3C", 0x44, 0xC7, 2, "(Pr550) NET mode operation command source selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param429= 0, 6, "20 75 24 01 30 3D", 0x44, 0xC7, 2, "(Pr551) PU mode operation command source selection", "", "", 1, 3, 2, 1, 1, 1, 0, , , , , 0; Param430= 0, 6, "20 75 24 01 30 41", 0x44, 0xC7, 2, "(Pr555) Current average time", "Sec", "", 1, 10, 10, 1, 1, 1, 0, , , , , 1; Param431= 0, 6, "20 75 24 01 30 42", 0x44, 0xC7, 2, "(Pr556) Data output mask time", "Sec", "", 0, 200, 0, 1, 1, 1, 0, , , , , 1; Param432= 0, 6, "20 75 24 01 30 49", 0x54, 0xC7, 2, "(Pr563) Energization time carryingover times", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param433= 0, 6, "20 75 24 01 30 4A", 0x54, 0xC7, 2, "(Pr564) Operating time carrying-over times", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param434= 0, 6, "20 75 24 01 30 4F", 0x44, 0xC7, 2, "(Pr569) Second motor speed control gain ", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param435= 0, 6, "20 75 24 01 30 51", 0x44, 0xC7, 2, "(Pr571) Holding time at a start", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param436= 0, 6, "20 75 24 01 30 54", 0x44, 0xC7, 2, "(Pr574) Second motor online auto tuning selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param437= 0, 6, "20 75 24 01 30 55", 0x44, 0xC7, 2, "(Pr575) Output interruption detection time", "Sec", "", 0, 65535, 10, 1, 1, 1, 0, , , , , 1; Param438= 0, 6, "20 75 24 01 30 56", 0x44, 0xC7, 2, "(Pr576) Output interruption detection level", "Hz", "", 0, 40000, 0, 1, 1, 1, 0, , , , , 2; Param439= 0, 6, "20 75 24 01 30 57", 0x44, 0xC7, 2, "(Pr577) Output interruption release level", "%", "", 9000, 11000, 10000, 1, 1, 1, 0, , , , , 1; Param440= 0, 6, "20 76 24 01 30 15", 0x44, 0xC7, 2, "(Pr611) Acceleration time at a restart", "Sec", "", 0, 65535, 50, 1, 1, 1, 0, , , , , 1; Param441= 0, 6, "20 76 24 01 30 5E", 0x44, 0xC7, 2, "(Pr684) Auto-tuning unit selection ", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param442= 0, 6, "20 78 24 01 30 0A", 0x44, 0xC7, 2, "(Pr800) Control system celection", "", "", 0, 20, 20, 1, 1, 1, 0, , , , , 0; Param443= 0, 6, "20 78 24 01 30 0D", 0x44, 0xC7, 2, "(Pr803) Constant output region torque characteristic selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param444= 0, 6, "20 78 24 01 30 0E", 0x44, 0xC7, 2, "(Pr804) Torque command source selection", "", "", 0, 6, 0, 1, 1, 1, 0, , , , , 0; Param445= 0, 6, "20 78 24 01 30 0F", 0x44, 0xC7, 2, "(Pr805) Torque command source (RAM)", "%", "", 600, 1400, 1000, 1, 1, 1, 0, , , , , 0; Param446= 0, 6, "20 78 24 01 30 10", 0x44, 0xC7, 2, "(Pr806) Torque command source (RAM,E2PROM)", "%", "", 600, 1400, 1000, 1, 1, 1, 0, , , , , 0; Param447= 0, 6, "20 78 24 01 30 11", 0x44, 0xC7, 2, "(Pr807) Speed restriction selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param448= 0, 6, "20 78 24 01 30 12", 0x44, 0xC7, 2, "(Pr808) Forward rotation speed restriction", "Hz", "", 0, 12000, 6000, 1, 1, 1, 0, , , , , 2; Param449= 0, 6, "20 78 24 01 30 13", 0x44, 0xC7, 2, "(Pr809) Reverse rotation speed restriction", "Hz", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param450= 0, 6, "20 78 24 01 30 14", 0x44, 0xC7, 2, "(Pr810) Torque restriction input method selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param451= 0, 6, "20 78 24 01 30 16", 0x44, 0xC7, 2, "(Pr812) Torque restriction level (regeneration)", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param452= 0, 6, "20 78 24 01 30 17", 0x44, 0xC7, 2, "(Pr813) Torque restriction level (3 quadrant)", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param453= 0, 6, "20 78 24 01 30 18", 0x44, 0xC7, 2, "(Pr814) Torque restriction level (4 quadrant)", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param454= 0, 6, "20 78 24 01 30 19", 0x44, 0xC7, 2, "(Pr815) Torque restriction level 2", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param455= 0, 6, "20 78 24 01 30 1A", 0x44, 0xC7, 2, "(Pr816) Acceleration torque restriction level ", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param456= 0, 6, "20 78 24 01 30 1B", 0x44, 0xC7, 2, "(Pr817) Deceleration torque restriction level ", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param457= 0, 6, "20 78 24 01 30 1C", 0x44, 0xC7, 2, "(Pr818) Easy gain tuning response level setting ", "", "", 1, 15, 2, 1, 1, 1, 0, , , , , 0; Param458= 0, 6, "20 78 24 01 30 1D", 0x44, 0xC7, 2, "(Pr819) Easy gain tuning selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param459= 0, 6, "20 78 24 01 30 1E", 0x44, 0xC7, 2, "(Pr820) Speed control P gain 1", "%", "", 0, 1000, 60, 1, 1, 1, 0, , , , , 0; Param460= 0, 6, "20 78 24 01 30 1F", 0x44, 0xC7, 2, "(Pr821) Speed control integral time 1", "Sec", "", 0, 20000, 333, 1, 1, 1, 0, , , , , 3; Param461= 0, 6, "20 78 24 01 30 20", 0x44, 0xC7, 2, "(Pr822) Speed setting filter 1", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 3; Param462= 0, 6, "20 78 24 01 30 22", 0x44, 0xC7, 2, "(Pr824) Torque control P gain 1", "%", "", 0, 200, 100, 1, 1, 1, 0, , , , , 0; Param463= 0, 6, "20 78 24 01 30 23", 0x44, 0xC7, 2, "(Pr825) Torque control integral time 1", "ms", "", 0, 5000, 50, 1, 1, 1, 0, , , , , 1; Param464= 0, 6, "20 78 24 01 30 24", 0x44, 0xC7, 2, "(Pr826) Torque setting filter 1", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 3; Param465= 0, 6, "20 78 24 01 30 25", 0x44, 0xC7, 2, "(Pr827) Torque detection filter 1", "Sec", "", 0, 100, 0, 1, 1, 1, 0, , , , , 3; Param466= 0, 6, "20 78 24 01 30 26", 0x44, 0xC7, 2, "(Pr828) Model speed control gain", "%", "", 0, 1000, 60, 1, 1, 1, 0, , , , , 0; Param467= 0, 6, "20 78 24 01 30 28", 0x44, 0xC7, 2, "(Pr830) Speed control P gain 2", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param468= 0, 6, "20 78 24 01 30 29", 0x44, 0xC7, 2, "(Pr831) Speed control integral time 2", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 3; Param469= 0, 6, "20 78 24 01 30 2A", 0x44, 0xC7, 2, "(Pr832) Speed setting filter 2", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 3; Param470= 0, 6, "20 78 24 01 30 2C", 0x44, 0xC7, 2, "(Pr834) Torque control P gain 2", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param471= 0, 6, "20 78 24 01 30 2D", 0x44, 0xC7, 2, "(Pr835) Torque control integral time 2", "ms", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param472= 0, 6, "20 78 24 01 30 2E", 0x44, 0xC7, 2, "(Pr836) Torque setting filter 2", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 3; Param473= 0, 6, "20 78 24 01 30 2F", 0x44, 0xC7, 2, "(Pr837) Torque detection filter 2", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 3; Param474= 0, 6, "20 78 24 01 30 32", 0x44, 0xC7, 2, "(Pr840) Torque bias selection", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param475= 0, 6, "20 78 24 01 30 33", 0x44, 0xC7, 2, "(Pr841) Torque bias 1", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param476= 0, 6, "20 78 24 01 30 34", 0x44, 0xC7, 2, "(Pr842) Torque bias 2", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param477= 0, 6, "20 78 24 01 30 35", 0x44, 0xC7, 2, "(Pr843) Torque bias 3", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param478= 0, 6, "20 78 24 01 30 36", 0x44, 0xC7, 2, "(Pr844) Torque bias filter", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 3; Param479= 0, 6, "20 78 24 01 30 37", 0x44, 0xC7, 2, "(Pr845) Torque bias operation time", "Sec", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param480= 0, 6, "20 78 24 01 30 38", 0x44, 0xC7, 2, "(Pr846) Torque bias balance compensation", "Volt", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param481= 0, 6, "20 78 24 01 30 39", 0x44, 0xC7, 2, "(Pr847) Fall-time torque bias No. 3 bias", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param482= 0, 6, "20 78 24 01 30 3A", 0x44, 0xC7, 2, "(Pr848) Fall-time torque bias No. 3 gain", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param483= 0, 6, "20 78 24 01 30 3B", 0x44, 0xC7, 2, "(Pr849) Analog input offset adjustment", "%", "", 0, 2000, 1000, 1, 1, 1, 0, , , , , 1; Param484= 0, 6, "20 78 24 01 30 3C", 0x44, 0xC7, 2, "(Pr850) Brakingoperation selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param485= 0, 6, "20 78 24 01 30 44", 0x44, 0xC7, 2, "(Pr858) tarminal 4 function selection", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param486= 0, 6, "20 78 24 01 30 48", 0x44, 0xC7, 2, "(Pr862) Notch filter constant", "", "", 0, 60, 0, 1, 1, 1, 0, , , , , 0; Param487= 0, 6, "20 78 24 01 30 49", 0x44, 0xC7, 2, "(Pr863) Notch filter depth", "", "", 0, 3, 0, 1, 1, 1, 0, , , , , 0; Param488= 0, 6, "20 78 24 01 30 4A", 0x44, 0xC7, 2, "(Pr864) Torque detection", "%", "", 0, 4000, 1500, 1, 1, 1, 0, , , , , 1; Param489= 0, 6, "20 78 24 01 30 4B", 0x44, 0xC7, 2, "(Pr865) Low speed detection", "Hz", "", 0, 40000, 150, 1, 1, 1, 0, , , , , 2; Param490= 0, 6, "20 78 24 01 30 4C", 0x44, 0xC7, 2, "(Pr866) Torque monitoring reference", "%", "", 0, 4000, 1500, 1, 1, 1, 0, , , , , 1; Param491= 0, 6, "20 78 24 01 30 4D", 0x44, 0xC7, 2, "(Pr867) AM output filter", "Sec", "", 0, 500, 1, 1, 1, 1, 0, , , , , 2; Param492= 0, 6, "20 78 24 01 30 4E", 0x44, 0xC7, 2, "(Pr868) No.1 terminal function assignment", "", "", 0, 65535, 0, 1, 1, 1, 0, , , , , 0; Param493= 0, 6, "20 78 24 01 30 52", 0x44, 0xC7, 2, "(Pr872) Input phase failure protection selection", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param494= 0, 6, "20 78 24 01 30 53", 0x44, 0xC7, 2, "(Pr873) Speed restriction", "rpm", "", 0, 3600, 600, 1, 1, 1, 0, , , , , 0; Param495= 0, 6, "20 78 24 01 30 54", 0x44, 0xC7, 2, "(Pr874) OLT level setting", "%", "", 0, 2000, 1500, 1, 1, 1, 0, , , , , 1; Param496= 0, 6, "20 78 24 01 30 55", 0x44, 0xC7, 2, "(Pr875) Fault definition", "", "", 0, 1, 0, 1, 1, 1, 0, , , , , 0; Param497= 0, 6, "20 78 24 01 30 57", 0x44, 0xC7, 2, "(Pr877) Speed feed forward control/model adaptive speed control selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param498= 0, 6, "20 78 24 01 30 58", 0x44, 0xC7, 2, "(Pr878) Speed feed forward filter", "Sec", "", 0, 100, 0, 1, 1, 1, 0, , , , , 2; Param499= 0, 6, "20 78 24 01 30 59", 0x44, 0xC7, 2, "(Pr879) Speed feed forward torque restriction", "%", "", 0, 4000, 1500, 1, 1, 1, 0, , , , , 1; Param500= 0, 6, "20 78 24 01 30 5A", 0x44, 0xC7, 2, "(Pr880) Load inertia ratio", "", "", 0, 2000, 70, 1, 1, 1, 0, , , , , 1; Param501= 0, 6, "20 78 24 01 30 5B", 0x44, 0xC7, 2, "(Pr881) Speed feed forward gain", "%", "", 0, 1000, 0, 1, 1, 1, 0, , , , , 0; Param502= 0, 6, "20 78 24 01 30 5C", 0x44, 0xC7, 2, "(Pr882) Regeneration avoidance operation selection", "", "", 0, 2, 0, 1, 1, 1, 0, , , , , 0; Param503= 0, 6, "20 78 24 01 30 5D", 0x44, 0xC7, 2, "(Pr883) Regeneration avoidance operation level", "Volt", "", 3000, 8000, 3800, 1, 1, 1, 0, , , , , 1; Param504= 0, 6, "20 78 24 01 30 5E", 0x44, 0xC7, 2, "(Pr884) Regeneration avoidance at deceleration detection sensitivity", "", "", 0, 5, 0, 1, 1, 1, 0, , , , , 0; Param505= 0, 6, "20 78 24 01 30 5F", 0x44, 0xC7, 2, "(Pr885) Regeneration avoidance compensation frequency limit value", "Hz", "", 0, 65535, 600, 1, 1, 1, 0, , , , , 2; Param506= 0, 6, "20 78 24 01 30 60", 0x44, 0xC7, 2, "(Pr886) Regeneration avoidance voltage gain", "%", "", 0, 2000, 1000, 1, 1, 1, 0, , , , , 1; Param507= 0, 6, "20 78 24 01 30 62", 0x54, 0xC7, 2, "(Pr888) Free parameter 1", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param508= 0, 6, "20 78 24 01 30 63", 0x54, 0xC7, 2, "(Pr889) Free parameter 2", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param509= 0, 6, "20 78 24 01 30 65", 0x44, 0xC7, 2, "(Pr891) Cumulative power monitor digit shifted times", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param510= 0, 6, "20 78 24 01 30 66", 0x44, 0xC7, 2, "(Pr892) Load factor", "%", "", 300, 1500, 1000, 1, 1, 1, 0, , , , , 1; Param511= 0, 6, "20 78 24 01 30 68", 0x44, 0xC7, 2, "(Pr894) Control selection during commercial power-supply operation", "", "", 0, 3, 0, 1, 1, 1, 0, , , , , 0; Param512= 0, 6, "20 78 24 01 30 69", 0x44, 0xC7, 2, "(Pr895) Power saving rate reference value", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param513= 0, 6, "20 78 24 01 30 6A", 0x44, 0xC7, 2, "(Pr896) Power unit cost", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 2; Param514= 0, 6, "20 78 24 01 30 6B", 0x44, 0xC7, 2, "(Pr897) Power saving monitor average time", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param515= 0, 6, "20 78 24 01 30 6C", 0x44, 0xC7, 2, "(Pr898) Power saving cumulative monitor clear", "", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 0; Param516= 0, 6, "20 78 24 01 30 6D", 0x44, 0xC7, 2, "(Pr899) Operation time rate (estimated value)", "%", "", 0, 65535, 65535, 1, 1, 1, 0, , , , , 1; Param517= 0, 6, "20 79 24 01 30 0A", 0x44, 0xC7, 2, "(Pr900) FM terminal calibration", "", "", 0, 8191, 1879, 1, 1, 1, 0, , , , , 0; Param518= 0, 6, "20 79 24 01 30 0B", 0x44, 0xC7, 2, "(Pr901) AM terminal calibration", "", "", 0, 8191, 3514, 1, 1, 1, 0, , , , , 0; Param519= 0, 6, "20 79 24 01 30 0C", 0x44, 0xC7, 2, "(Pr902) Terminal 2 frequency setting bias frequency", "Hz", "", 0, 40000, 0, 1, 1, 1, 0, , , , , 2; Param520= 0, 6, "20 79 24 02 30 0C", 0x44, 0xC7, 2, "(Pr902) Terminal 2 frequency setting bias", "%", "", 0, 3000, 0, 1, 1, 1, 0, , , , , 1; Param521= 0, 6, "20 79 24 01 30 0D", 0x44, 0xC7, 2, "(Pr903) Terminal 2 frequency setting gain frequency", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param522= 0, 6, "20 79 24 02 30 0D", 0x44, 0xC7, 2, "(Pr903) Terminal 2 frequency setting gain", "%", "", 0, 3000, 1000, 1, 1, 1, 0, , , , , 1; Param523= 0, 6, "20 79 24 01 30 0E", 0x44, 0xC7, 2, "(Pr904) Terminal 4 frequency setting bias frequency", "Hz", "", 0, 40000, 0, 1, 1, 1, 0, , , , , 2; Param524= 0, 6, "20 79 24 02 30 0E", 0x44, 0xC7, 2, "(Pr904) Terminal 4 frequency setting bias", "%", "", 0, 3000, 200, 1, 1, 1, 0, , , , , 1; Param525= 0, 6, "20 79 24 01 30 0F", 0x44, 0xC7, 2, "(Pr905) Terminal 4 frequency setting gain frequency", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param526= 0, 6, "20 79 24 02 30 0F", 0x44, 0xC7, 2, "(Pr905) Terminal 4 frequency setting gain", "%", "", 0, 3000, 1000, 1, 1, 1, 0, , , , , 1; Param527= 0, 6, "20 79 24 01 30 1B", 0x44, 0xC7, 2, "(Pr917) Terminal 1 bias frequency (Speed)", "Hz", "", 0, 40000, 0, 1, 1, 1, 0, , , , , 2; Param528= 0, 6, "20 79 24 02 30 1B", 0x44, 0xC7, 2, "(Pr917) Terminal 1 bias (Speed)", "%", "", 0, 3000, 0, 1, 1, 1, 0, , , , , 1; Param529= 0, 6, "20 79 24 01 30 1C", 0x44, 0xC7, 2, "(Pr918) Terminal 1gain frequency (Speed)", "Hz", "", 0, 40000, 6000, 1, 1, 1, 0, , , , , 2; Param530= 0, 6, "20 79 24 02 30 1C", 0x44, 0xC7, 2, "(Pr918) Terminal 1gain (Speed)", "%", "", 0, 3000, 1000, 1, 1, 1, 0, , , , , 1; Param531= 0, 6, "20 79 24 01 30 1D", 0x44, 0xC7, 2, "(Pr919) Terminal 1bias operation (torque/magnetic flux)", "%", "", 0, 4000, 0, 1, 1, 1, 0, , , , , 1; Param532= 0, 6, "20 79 24 02 30 1D", 0x44, 0xC7, 2, "(Pr919) Terminal 1bias (torque/magnetic flux)", "%", "", 0, 3000, 0, 1, 1, 1, 0, , , , , 1; Param533= 0, 6, "20 79 24 01 30 1E", 0x44, 0xC7, 2, "(Pr920) Terminal 1gain operation (torque/magnetic flux)", "%", "", 0, 4000, 1500, 1, 1, 1, 0, , , , , 1; Param534= 0, 6, "20 79 24 02 30 1E", 0x44, 0xC7, 2, "(Pr920) Terminal 1gain (torque/magnetic flux)", "%", "", 0, 3000, 1000, 1, 1, 1, 0, , , , , 1; Param535= 0, 6, "20 79 24 01 30 2A", 0x44, 0xC7, 2, "(Pr932) Terminal 4 bias operation (torque/magnetic flux)", "%", "", 0, 4000, 0, 1, 1, 1, 0, , , , , 1; Param536= 0, 6, "20 79 24 02 30 2A", 0x44, 0xC7, 2, "(Pr932) Terminal 4 bias (torque/magnetic flux)", "%", "", 0, 3000, 200, 1, 1, 1, 0, , , , , 1; Param537= 0, 6, "20 79 24 01 30 2B", 0x44, 0xC7, 2, "(Pr933) Terminal 4 gain operation (torque/magnetic flux)", "%", "", 0, 4000, 1500, 1, 1, 1, 0, , , , , 1; Param538= 0, 6, "20 79 24 02 30 2B", 0x44, 0xC7, 2, "(Pr933) Terminal 4 gain (torque/magnetic flux)", "%", "", 0, 3000, 1000, 1, 1, 1, 0, , , , , 1; Param539= 0, 6, "20 79 24 01 30 63", 0x44, 0xC7, 2, "(Pr989) Parameter copy alarm release", "", "", 10, 100, 10, 1, 1, 1, 0, , , , , 0; Param540= 0, 6, "20 79 24 01 30 64", 0x44, 0xC7, 2, "(Pr990) PU buzzer control", "", "", 0, 1, 1, 1, 1, 1, 0, , , , , 0; Param541= 0, 6, "20 79 24 01 30 65", 0x44, 0xC7, 2, "(Pr991) PU contrast adjustment", "", "", 0, 63, 58, 1, 1, 1, 0, , , , , 0; [EnumPar] Param1 = "Type 0", "Type 1", "Type 2", "Type 3", "Type 4", "Type 5", "Type 6", "Type 7"; Param3 = "No", "Yes"; $ Run1 Param4 = "No", "Yes"; $ Run2 Param5 = "Local", "Network"; $ NetCtrl Param6 = $ State "Vendor Specific", "Startup", "Not_Ready", "Ready", "Enabled", "Stopping", "Fault_Stop", "Faulted"; Param7 = "No", "Yes"; $ Running1 Param8 = "No", "Yes"; $ Running2 Param9 = "Not Ready", "Ready"; $ Ready Param10 = "Not Faulted", "Faulted"; $ Faulted Param11 = "No Action", "Fault Reset"; $ Fault Reset Param12 = "Local", "Network"; $ Control from Net Param15 = "Not At Reference", "At Reference"; $ At Reference Param16 = "Local", "Network"; $ Net Reference Param17 = $ Drive Mode "Vendor Specific"; Param26 = "Local", "Network"; $ Reference from Net Param29 = $ State "EXT(Read)", "PU(Read)", "EXT JOG(Read)", "PU JOG(Read)", "NET(Read)", "PU+E(Read)", "", "", "", "", "", "", "", "", "", "", "EXT(Write)", "PU(Write)", "EXT JOG(Write)", "PU JOG(Write)", "NET(Write)"; [Groups] Group1= "Motor Data",2, 1 , 2 ; Group2= "Control Supervisor",12, 3 , 4 , 5 , 6 , 7 , 8 , 9 , 10 , 11 , 12 , 13 , 14; Group3= "AC Drive",23, 15 , 16 , 17 , 18 , 19 , 20 , 21 , 22 , 23 , 24 , 25 , 26 , 27 , 28 , 29 , 30 , 31 , 32 , 33 , 34 , 35 , 36 , 37; Group4= "Monitor",27, 38 , 39 , 40 , 41 , 42 , 43 , 44 , 45 , 46 , 47 , 48 , 49 , 50 , 51 , 52 , 53 , 54 , 55 , 56 , 57 , 58 , 59 , 60 , 61 , 62 , 63 , 64; Group5= "Basic Functions",9, 65 , 66 , 67 , 68 , 69 , 70 , 71 , 72 , 73; Group6= "Standard Operation Functions",28, 74 , 75 , 76 , 77 , 78 , 79 , 80 , 81 , 82 , 83 , 84 , 85 , 86 , 87 , 88 , 89 , 90 , 91 , 92 , 93 , 94 , 95 , 96 , 97 , 98 , 99 , 100 , 101; Group7= "Output Terminal Functions",3, 102 , 103 , 104; Group8= "Second Functions",7, 105 , 106 , 107 , 108 , 109 , 110 , 111; Group9= "Display Functions",8, 112 , 113 , 114 , 267 , 432 , 433 , 490 , 491; Group10= "Automatic Restart Functions",3, 115 , 116 , 440; Group11="Additional Functions",17, 117 , 201, 209, 210, 245, 246, 252, 253, 254, 342, 354, 483, 486, 487, 488, 489, 493; Group12="Operation Selection Functions",30, 118 , 119 , 120 , 121 , 122 , 123 , 124 , 125 , 126 , 127 , 128 , 129 , 130 , 131 , 132 , 133 , 134 , 135 , 136 , 287 , 288 , 442 , 443 , 444 , 445 , 446 , 447 , 448 , 449 , 496; Group13="5-point flexible V/F characteristics",10, 143 , 144 , 145 , 146 , 147 , 148 , 149 , 150 , 151 , 152; Group14="Communication Functions",8, 160 , 161 , 162 , 163 , 164 , 165 , 166 , 167; Group15="PID control",11, 170 , 171 , 172 , 173 , 174 , 175 , 176 , 177 , 437 , 438 , 439; Group16="Commercial power supply inverter switch-over",6,178 , 179 , 180 , 181 , 182 , 200; Group17="Backlash",4, 183, 184 , 185 , 186; Group18="Display",1, 187; Group19="PU",3, 188 , 540 , 541; Group20="Current detection",8, 189 , 190 , 191 , 192 , 193 , 194 , 207 , 208; Group21="Sub function",10, 195 , 196 , 197 , 198 , 199 , 202 , 243 , 247 , 435 , 539; Group22="Automatic restart after instantaneous power failure",4,203 , 204 , 205 , 206; Group23="Cumulative monitor clear",2, 211 , 212; Group24="User functions",3, 213 , 214 , 215; Group25="Terminal assignment functions",22, 216 , 217 , 218 , 219 , 220 , 221 , 222 , 223 , 224 , 225 , 226 , 227 , 228 , 229 , 230 , 231 , 232 , 233 , 234 , 484 , 485 , 492; Group26="Multi-speed operation",8, 235 , 236 , 237 , 238 , 239 , 240 , 241 , 242; Group27="Analog input",2, 244 , 266; Group28="Slip compensation",3, 248 , 249 , 250; Group29="Stop selection function",1, 251; Group30="Life check",5, 255 , 256 , 257 , 258 , 259; Group31="Power failure stop function",7, 260 , 261 , 262 , 263 , 264 , 265 , 289; Group32="Digital input",10, 290 , 291 , 292 , 293 , 294 , 295 , 296 , 316 , 374 , 375; Group33="Analog output",9, 297 , 298 , 299 , 300 , 301 , 302 , 303 , 314 , 315; Group34="Digital output",7, 304 , 305 , 306 , 307 , 308 , 309 , 310; Group35="Relay output",3, 311 , 312 , 313; Group36="RS-485 communication",13, 317 , 318 , 319 , 320 , 321 , 322 , 323 , 324 , 325 , 326 , 327 , 328 , 329; Group37="DeviceNet Functions",3, 330 , 331 , 332; Group38="Remote output",3, 413 , 414 , 415; Group39="Communication error",3, 416 , 417 , 418; Group40="Maintenance",2, 419 , 420; Group41="Communication",5, 425 , 426 , 427 , 428 , 429; Group42="Current average monitor",2, 430 , 431; Group43="Regeneration avoidance function",5, 502 , 503 , 504 , 505 , 506; Group44="Free parameter",2, 507 , 508; Group45="Energy saving monitor",8, 509 , 510 , 511 , 512 , 513 , 514 , 515 , 516; Group46="Calibration functions",24, 168 , 169 , 517 , 518 , 519 , 520 , 521 , 522 , 523 , 524 , 525 , 526 , 527 , 528 , 529 , 530 , 531 , 532 , 533 , 534 , 535 , 536 , 537 , 538; Group47="Third Functions",7, 153 , 154 , 155 , 156 , 157 , 158 , 159; Group48="High-speed frequency control",4, 269 , 270 , 271 , 272; Group49="Stop on contact",3, 268 , 273 , 274; Group50="Break sequence functions",11, 275 , 276 , 277 , 278 , 279 , 280 , 281 , 282 , 283 , 284 , 285; Group51="Pulse input and output",4, 286 , 359 , 360 , 361; Group52="S-Curve",8, 355 , 356 , 357 , 358 , 421 , 422 , 423 , 424; Group53="Control system functions",30, 353 , 450 , 451 , 452 , 453 , 454 , 455 , 456 , 457 , 458 , 459 , 460 , 461 , 462 , 463 , 464 , 465 , 466 , 467 , 468 , 469 , 470 , 471 , 472 , 473 , 497 , 498 , 499 , 500 , 501; Group54="Protective Functions",2, 494 , 495; Group55="Motor constants",15, 137 , 138 , 139 , 140 , 141 , 142 , 376 , 377 , 378 , 379 , 380 , 381 , 434 , 436 , 441; Group56="User Functions",3, 213 , 214 , 215; Group57="Orientation",16, 333 , 334 , 335 , 336 , 337 , 338 , 339 , 340 , 341 , 343 , 344 , 345 , 346 , 347 , 348 , 349; Group58="Encoder feedback control",3, 350 , 351 , 352; Group59="Position control",43, 362 , 363 , 364 , 365 , 366 , 367 , 368 , 369 , 370 , 371 , 372 , 373 , 382 , 383 , 384 , 385 , 386 , 387 , 388 , 389 , 390 , 391 , 392 , 393 , 394 , 395 , 396 , 397 , 398 , 399 , 400 , 401 , 402 , 403 , 404 , 405 , 406 , 407 , 408 , 409 , 410 , 411 , 412; Group60="Current average monitor",2, 555 , 556; Group61="Torque biases",9, 474 , 475 , 476 , 477 , 478 , 479 , 480 , 481 , 482;